MIL-STD-1105E (NOTICE 1), MILITARY STANDARD, SANITARY STANDARDS FOR BAKERIES (16 SEP 1998) [REFER TO MIL-STD-3006]., MIL-STD-1105E, dated 27 December 1991, is hereby canceled without replacement.

MIL-STD-1105E, MILITARY STANDARD, SANITARY STANDARDS FOR BAKERIES (27 DEC 1991) [S/S BY MIL-STD-3006]., This standard sets forth the general sanitary requirements for bakeries.

MIL-STD-1131B (NOTICE 1), MILITARY STANDARD, STORAGE SHELF LIFE AND REFORMING PROCEDURES FOR ALUMINUM ELECTROLYTIC FIXED CAPACITORS (7 JUL 1999) [MIL-HDBK-1131]., MIL-STD-1131B is hereby canceled. However, the technical information and the lessons learned from this standard have been preserved in MIL-HDBK-1131. MIL-HDBK-1131 is for guidance only and should not be cited as a requirement, but the information in the handbook may be useful in determining or evaluating requirements.

MIL-STD-1156C, MILITARY STANDARD, SANITARY STANDARDS FOR SOFT DRINK PLANTS (8 JAN 1982)., This standard establishes the general sanitary requirements for plants that supply soft drinks to the Armed Forces.

MIL-STD-1167C, MILITARY STANDARD, AMMUNITION DATA CARD (5 AUG 1985)., This standard establishes and describes the preparation, utilization and distribution of Ammunition Data Cards.

MIL-STD-1168B, MILITARY STANDARD, AMMUNITION LOT NUMBERING AND AMMUNITION DATA CARD (10 JUN 1998). The purpose of lot numbering ammunition items and creation of ammunition data cards as outlined herein is to provide the identification of homogeneous materiel necessary to assure accurate control of items during development and experimental stages; during the movement of items from production line to production line, from plant to plant, from plant to storage facilities; while at test facilities or in the field; for issue to the using services; to enable the proper establishment and maintenance of surveillance records; and to provide a means for properly identifying materiel when withdrawal of defective, deteriorated, hazardous or obsolete ammunition and explosive materiel from service is required.

MIL-STD-1180B (NOTICE 1), MILITARY STANDARD, SAFETY STANDARDS FOR MILITARY GROUND VEHICLES (7 AUG 1991)., THE FOLLOWING PAGES OF MIL-STD-1180B, HAVE BEEN REVISED AND SUPERSEDE THE PAGES LISTED:

MIL-STD-1180B, MILITARY STANDARD, SAFETY STANDARDS FOR MILITARY GROUND VEHICLES (20 SEPT 1986)., This standard applies to military ground vehicles listed in table 1. Administrative vehicles and construction equipment/material handling equipment acquired by the Department of Defense are not included in this military standard since they are usually built to the manufacturer commercial specifications and are required to meet all applicable standards.

MIL-STD-1183 (NOTICE 1), MILITARY STANDARD, WELDING, GAS, STEELS, CONSTRUCTIONAL, READILY WELDABLE, FOR LOW STRESSED JOINTS (9 JUL 1996) [SUPERSEDES MIL-W-62163) [S/S BY AWS-D1.3]., MIL-STD-1183(AT), dated 12 December 1978, is hereby canceled. Future acquisitions should refer to American Welding Society (AWS) D 1.3 ?Structural Welding Code-Sheet Steel?.

MIL-STD-1183, MILITARY STANDARD, WELDING, GAS, STEELS, CONSTRUCTIONAL, READILY WELDABLE, FOR LOW STRESSED JOINTS (12 DEC 1978) [SUPERSEDES MIL-W-62163) [S/S BY AWS-D1.3]., This standard covers oxy-acetylene gas welding of readily weldable constructional steels when joint strength is not a consideration in the function of the part.

MIL-STD-1184, MILITARY STANDARD, ELECTRICAL COMPONENTS FOR AUTOMOTIVE VEHICLES, WATER-PROOFNESS TESTS (20 APR 1979) [SUPERSEDING MIL-E-13856B]., This standard establishes uniform test methods for determining the waterproofness (resistance to the effects of water) of electrical components of automotive vehicles.

MIL-STD-1185 (NOTICE 1), DEPARTMENT OF DEFENSE MANUFACTURING PROCESS STANDARD, WELDING, HIGH HARDNESS ARMOR (18 JUN 2003) [SUPERSEDES MIL-W-62162(AT)]., MIL-STD-1185, dated 31 December 1979, is hereby cancelled. Future acquisitions should refer to TACOM Drawing 12479550, ?Ground Combat Vehicle Welding Code ? Steel?.

MIL-STD-1185, DEPARTMENT OF DEFENSE MANUFACTURING PROCESS STANDARD, WELDING, HIGH HARDNESS ARMOR (31 DEC 1979) [SUPERSEDES MIL-W-62162(AT)]., This standard covers the fabrication of weldments constructed of 1 inch (25.4 mm) maximum thickness, high hardness, rolled armor and steel attachments welded to the armor. It contains information relating to preparation and submission of welding procedures, preparation of workmanship specimens, joint welding procedures, inspection of weldments and radiographic data.

MIL-STD-1190, MILITARY STANDARD, MINIMUM GUIDELINES FOR LEVEL C PRESERVATION, PACKING AND MARKING (10 SEP 1986) [S/S BY ASTM-D3951 AND MIL-STD-2073-1]., This standard establishes minimum Army packaging, using federal or military specifications, for protection of equipment from supply source to the first receiving activity and subsequent redistribution.

MIL-STD-1201C (NOTICE 1), MILITARY STANDARD, ETHYL ALCOHOL (ETHANOL), TECHNICAL AND DENATURED GRADES (5 DEC 1995)., MIL-STD-1201C dated 4 April 1994 is hereby canceled without replacement.

MIL-STD-1201C, MILITARY STANDARD, ETHYL ALCOHOL (ETHANOL), TECHNICAL AND DENATURED GRADES (4 APR 1994). This standard is a presentation of nomenclature, Chemical Abstracts Service Registry Numbers, symbols, physical and chemical properties and requirements, military and typical commercial uses, directions for use, packaging data, labeling, general safety precautions, storage information, and shelf life of all military standard technical and denatured grades, ethyl alcohol. This standard does not necessarily include all classifications of the item represented by the title of those which are commercially available. It does contain items preferred for use in the selection of technical and denatured grades, ethyl alcohol, for application by the Department of Defense.

MIL-STD-1202A (NOTICE 1), MILITARY STANDARD, FACESHIELD, INDUSTRIAL (28 JUL 1998)., MIL-STD-1202A is hereby canceled without replacement.

MIL-STD-1202A, MILITARY STANDARD, FACESHIELD, INDUSTRIAL (19 AUG 1988)., The purpose of this standard is to present the nomenclature, specification requirements, military uses, and safety information for industrial faceshields. This standard does not necessarily include all those items which are commercially available. It does contain items preferred for use in the selection of industrial faceshields for the application by the Department of Defense.

MIL-STD-1203B (NOTICE 1), MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (ALUMINUM CHLORIDE THROUGH BORON NITRIDE) (9 FEB 1998)., MIL-STD-1203B is hereby canceled without replacement.

MIL-STD-1203B, MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (ALUMINUM CHLORIDE THROUGH BORON NITRIDE) (26 JULY 1991)., This standard is a presentation of nomenclature, formulas, physical and chemical properties, specification requirements, military and typical commercial uses, safety information, storage information, and disposal information for in organic salts and compounds, technical grade, (aluminum chloride through boron nitride).

MIL-STD-1204C (NOTICE 1), MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (CADMIUM CARBONATE THROUGH CUPRIC SULFATE) (9 FEB 1998)., MIL-STD-1204C is hereby canceled without replacement.

MIL-STD-1204C, MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (CADMIUM CARBONATE THROUGH CUPRIC SULFATE) (4 SEPT 1990)., This standard is a presentation of nomenclature, formulas, physical and chemical properties, specification requirements, military and typical commercial uses, safety information, storage information and disposal information for inorganic salts and compounds, technical grade (cadmium carbonate through cupric sulfate.) This standard does not include all of the items represented by the title or all those items which are commercially available. It does contain items preferred for use in the selection of inorganic salts and compounds technical grade (cadmium carbonate through cupric sulfate) for application by the Department of Defense.

MIL-STD-1205B (NOTICE 1), MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (FERRIC CHLORIDE THROUGH LITHIUM TETRAFLUOROBORATE) (9 FEB 1998)., MIL-STD-1205B, dated 28 May 1993, is hereby canceled without replacement.

MIL-STD-1205B, MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (FERRIC CHLORIDE THROUGH LITHIUM TETRAFLUOROBORATE) (28 MAY 1993)., This standard is a presentation of nomenclature, Chemical Abstracts Service Registry Numbers, formulas, physical and chemical properties, specification requirements, military and typical commercial uses, safety information, storage information and disposal information for inorganic salts and compounds, technical grade (ferric chloride through lithium tetrafluoroborate). This standard does not include all of the items represented by the title of all those items which are commercially available. It does contain items preferred for use in the selection of inorganic salts and compounds, technical grade (ferric chloride through lithium tetrafluoroborate), for application by the Department of Defense.

MIL-STD-1206B (NOTICE 1), MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (MAGNESIUM CARBONATE THROUGH PHOSPHOROUS TRICHLORIDE) (9 FEB 1998)., MIL-STD-1206B, dated 14 June 1993, is hereby canceled without replacement.

MIL-STD-1206B, MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (MAGNESIUM CARBONATE THROUGH PHOSPHORUS TRICHLORIDE) (14 JUN 1993)., This standard is a presentation of nomenclature, Chemical Abstracts Service Registry Numbers, formulas, physical and chemical properties, specification requirements, military and typical commercial uses, safety information, storage information and disposal information for inorganic salts and compounds, technical grade (magnesium carbonate through phosphorus trichloride). This standard does not include all of the items represented by the title or all those items which are commercially available. It does contain items preferred for use in the selection of inorganic salts and compounds, technical grade (magnesium carbonate through phosphorus trichloride), for application by the Department of Defense.

MIL-STD-1207 (NOTICE 1), MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (POTASSIUM BICARBONATE THROUGH SILVER CYANIDE (9 FEB 1998)., MIL-STD-1207B, dated 23 November 1987, is hereby canceled without replacement.

MIL-STD-1207B, MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (POTASSIUM BICARBONATE THROUGH SILVER CYANIDE) (METRIC) (23 NOV 1987)., The purpose of this standard is to present the nomenclature, formulas, physical and chemical properties, specification requirements, military and typical commercial uses, safety information, storage information and disposal information for inorganic salts and compounds, technical grade (potassium bicarbonate through silver cyanide). This standard does not necessarily include all of those items which are commercially available. It does contain items preferred for use in the selection of inorganic compounds, for application by the Department of Defense.

MIL-STD-1208B (NOTICE 1), MILITARY STANDARD, INORGANIC SODIUM SALTS AND COMPOUNDS, TECHNICAL GRADE (SODIUM BICARBONATE THROUGH SODIUM TRIPOLYPHOSPHATE) (9 FEB 1998)., MIL-STD-1208B, dated 25 September 1991, is hereby canceled without replacement.

MIL-STD-1208B, MILITARY STANDARD, INORGANIC SODIUM SALTS AND COMPOUNDS, TECHNICAL GRADE (SODIUM BICARBONATE THROUGH SODIUM TRIPOLYPHOSPHATE) (25 SEPT 1991)., This standard is a presentation of nomenclature, formulas, physical and chemical properties, specification requirements, military and typical commercial uses, safety information, storage information and disposal information for inorganic salts and compounds, technical grade (sodium bicarbonate through sodium tripolyphosphate). This standard does not include all of the items represented by the title or all of those items which are not commercially available. It does contain items preferred for use in the selection of inorganic salts and compounds, technical grade (sodium bicarbonate through sodium tripolyphosphate), for application by the Department of Defense.

MIL-STD-1209B (NOTICE 1), MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (STRONTIUM CARBONATE THROUGH ZIRCONIUM CARBIDE) (10 FEB 1998)., MIL-STD-1209B, dated 23 June 1993, is hereby canceled without replacement.

MIL-STD-1209B, MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS, TECHNICAL GRADE (STRONTIUM CARBONATE THROUGH ZIRCONIUM CARBIDE) (23 JUN 1993)., This standard is a presentation of nomenclature, Chemical Abstracts Service Registry Numbers, formulas, physical and chemical properties, specification requirements, military and typical commercial uses, safety information, storage information and disposal information for inorganic salts and compounds, technical grade (strontium carbonate through zirconium carbide). This standard does not include all of the items represented by the title or all those which are commercially available. It does contain items preferred for use in the selection of inorganic salts and compounds, technical grade (strontium carbonate through zirconium carbide), for application by the Department of Defense.

MIL-STD-1210B (NOTICE 1), MILITARY STANDARD FOG AND ICE PREVENTIVE COMPOUNDS (5 DEC 1995)., MIL-STD-1210B dated 30 June 1972 is hereby canceled without replacement.

MIL-STD-1210B, MILITARY STANDARD, FOG AND ICE PREVENTIVE COMPOUNDS (30 JUN 1972)., This standard is a presentation of nomenclature, symbols, physical and chemical properties and requirements, military and typical commercial uses, directions for use, packaging data, labeling, general safety precautions, storage information, and shelf life of all military standard fog and ice preventative compounds.

MIL-STD-1211 (NOTICE 1), MILITARY STANDARD, INDICATORS (5 MAR 1990)., MIL-STD-1211, dated 18 June 1969, is hereby canceled.

MIL-STD-1211, MILITARY STANDARD, INDICATORS (18 JUL 1969). This standard is a presentation of nomenclature, symbols, chemical and physical properties and requirements, military use, directions for use, packaging data, labeling, storage information, and shelf life of all military standard indicators.

MIL-STD-1212A (NOTICE 1), MILITARY STANDARD, INDUSTRIAL SAFETY BELTS, STRAPS, AND RELATED EQUIPMENT (5 DEC 1995)., MIL-STD-1212A, dated 21 December 1988, is hereby canceled without replacement.

MIL-STD-1212A, MILITARY STANDARD, INDUSTRIAL SAFETY BELTS, STRAPS, AND RELATED EQUIPMENT (21 DEC 1988)., The purpose of this standard fs to present the nomenclature, specification requirements, military uses, and safety information for industrial safety belts, straps, harnesses, lanyards, and related equipment. The standard does not necessarily include all of those items which are commercially available. It does contain items preferred for use in the selection of industrial safety belts, straps, harnesses, lanyards, and related equipment, for application by the Department of Defense.

MIL-STD-1213A (NOTICE 1), MILITARY STANDARD, ORGANIC LABORATORY REAGENTS (INCLUDING ACS AND USP/NF) (10 FEB 1998)., MIL-STD-1213A, dated 8 February 1988, is hereby canceled without replacement.

MIL-STD-1213A, MILITARY STANDARD, ORGANIC LABORATORY REAGENTS (INCLUDING ACS AND USP/NF) (8 FEB 1988)., This standard is a presentation of nomenclature, formulas, physical and chemical properties, specification requirements, military uses, safety information, storage information and disposal information for organic laboratory reagents.

MIL-STD-1214A (NOTICE 1), MILITARY STANDARD, ESTERS AND METAL ORGANICS, TECHNICAL GRADE (10 FEB 1998)., MIL-STD-1214A, dated 28 September 1990, is hereby canceled without replacement.

MIL-STD-1214A, MILITARY STANDARD, ESTERS AND METAL ORGANICS, TECHNICAL GRADE (28 SEPT 1990)., This standard is a presentation of nomenclature, formulas, physical and chemical properties, specification requirements, military and typical commercial uses, safety information, storage information and disposal information for esters and metal organics, technical grade.

MIL-STD-1216A (NOTICE 1), MILITARY STANDARD, PREVENTIVE COMPOUNDS (CORROSION) AND INHIBITORS (5 DEC 1995)., MIL-STD-1216A dated 2 October 1990, is hereby canceled without replacement.

MIL-STD-1216A, MILITARY STANDARD, PREVENTIVE COMPOUNDS (CORROSION) AND INHIBITORS (2 OCT 1990)., This standard is a presentation of nomenclature, symbols, physical and chemical properties and requirements, military and typical commercial uses, directions for use, packaging data, labeling, general safety precautions, storage information, and shelf life of military corrosion preventive compounds and inhibitors coming under FSC 6850.

MIL-STD-1217C (NOTICE 1), MILITARY STANDARD, ORGANIC ACIDS AND ACID ANHYDRIDES, TECHNICAL GRADE (10 FEB 1998)., MIL-STD-1217C, dated 30 September 1991, is hereby canceled without replacement.

MIL-STD-1217C, MILITARY STANDARD, ORGANIC ACIDS AND ACID ANHYDRIDES, TECHNICAL GRADE (30 SEPT 1991)., This standard is a presentation of nomenclature, symbols, physical and chemical properties and requirements, military and typical commercial uses, directions for use, packaging data, labeling, general safety precautions, storage information, shelf life and disposal instructions for military standard organic acids.

MIL-STD-1218 (NOTICE 1), MILITARY STANDARD, ACS CHEMICALS (9 NOV 1990)., MIL-STD-1218, dated 6 June 1969 is hereby canceled without replacement.

MIL-STD-1218, MILITARY STANDARD, ACS CHEMICALS (6 JUNE 1969)., This standard is a presentation of nomenclature, symbols, physical and chemical properties and requirements, typical military uses, packaging data and labeling, storage information, and shelf life of military standard ACS grade chemicals.

MIL-STD-1220B (NOTICE 1), MILITARY STANDARD, ALCOHOLS AND AMINES, TECHNICAL GRADE (9 FEB 1998)., MIL-STD-1220B, dated 23 September 1991, is hereby canceled without replacement.

MIL-STD-1220B, MILITARY STANDARD, ALCOHOLS AND AMINES, TECHNICAL GRADE (23 SEPT 1991)., This standard is a presentation of nomenclature, formulas, physical and chemical properties, specification requirements, military and typical commercial uses, safety information, storage information and disposal information for aldehydes and ketones, technical grade.

MIL-STD-1221A, MILITARY STANDARD, PROTECTIVE COMPOUNDS (FOR PERSONNEL) (16 JULY 1979)., This standard is a presentation of nomenclature, symbols, physical and chemical properties and requirements, military and typical commercial uses, directions for use, packaging data, labeling, general safety precautions, storage information, disposal data, toxicity data and shelf life of all military standard protective compounds (for personnel).

MIL-STD-1221B (NOTICE 1), MILITARY STANDARD, PROTECTIVE COMPOUNDS (FOR PERSONNEL) (5 DEC 1995)., MIL-STD-1221B dated 28 September 1990 is hereby canceled without replacement.

MIL-STD-1221B, MILITARY STANDARD, PROTECTIVE COMPOUNDS (FOR PERSONNEL) (28 SEPT 1990)., This standard is a presentation of nomenclature, symbols, physical and chemical properties and requirements, military and typical commercial uses, directions for use, packaging data, labeling, general safety precautions, storage information, disposal data, toxicity data and shelf life of all military standard protective compounds (for personnel).

MIL-STD-1222 (NOTICE 1), MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS ANALYZED REAGENT AND REAGENT GRADE (20 SEPT 1991)., MIL-STD-1222 dated 5 June 1969 is hereby canceled without replacement.

MIL-STD-1222, MILITARY STANDARD, INORGANIC SALTS AND COMPOUNDS,ANALYZED REAGENT AND REAGENT GRADE (5 JUN 1969). This standard is a presentation of nomenclature, formulas, chemical and physical properties and requirements, military use, packaging data, labeling, storage information, and shelf life of all military inorganic salts and compounds, analyzed reagent and reagent grade. This standard does not necessarily include all classifications of the items represented by the title or those which are commercially available. It does contain items preferred for use in the selection of inorganic salts and compounds, analyzed reagent and reagent grade for application by the Department of Defense.

MIL-STD-1223 (NOTICE 1), MILITARY STANDARD, NONTACTICAL WHEELED VEHICLES TREATMENT, PAINTING, IDENTIFICATION MARKING AND DATA PLATE STANDARDS (17 APR 1998) [S/S BY MIL-HDBK-1223]., MIL-STD-1223AC, dated 1 August 1991, is hereby cancelled without replacement; however, the instructional information from this standard has been preserved in its entirety in MIL-HDBK-1223. MIL-HDBK-1223 is for guidance only and should not be cited as a requirement.

MIL-STD-1223AC, MILITARY STANDARD, NONTACTICAL WHEELED VEHICLES TREATMENT, PAINTING, IDENTIFICATION MARKING AND DATA PLATE STANDARDS (1 AUG 1991)., This standard prescribes requirements for treatment, painting, identification marking and data plates for self propelled and towed vehicles procured for general nontactical use by the government.

MIL-STD-1227B (NOTICE 1), MILITARY STANDARD, ENGINE, GASOLINE: AIR-COOLED, 3 BHP 4-CYCLE, MILITARY DESIGN, MODEL 2A016, INSTALLATION PROCEDURES (24 FEB 1976)., TO ALL HOLDERS 0F MIL-STD-1227B THE FOLLOWING PEN AND INK CHANGES SHALL BE MADE:

MIL-STD-1227B (NOTICE 2), MILITARY STANDARD, ENGINE, GASOLINE: AIR COOLED, 3 BHP 4-CYCLE, MILITARY DESIGN MODEL 2A016 INSTALLATION PROCEDURES (16 NOV 1987)., Military Standard MIL-STD-1227B, dated 13 September 1972 has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1227B, MILITARY STANDARD, ENGINE, GASOLINE: AIR-COOLED, 3 BHP, 4-CYCLE, MILITARY DESIGN, MODEL 2A016, INSTALLATION PROCEDURES (13 SEPT 1972)., This standard covers the recommended installation procedure for the model 2A016, 3 hp, military design engine.

MIL-STD-1233, MILITARY STANDARD., PROCEDURES FOR DETERMINING PARTICLE SIZE, PARTICLE SIZE DISTRIBUTION, AND PACKED DENSITY OF POWDERED MATERIALS (21 MAR 1962) [SUPERSEDING MIL-STD-707].,

MIL-STD-1234 (NOTICE 1), MILITARY STANDARD, PYROTECHNICS: SAMPLING INSPECTION AND TESTING (18 DEC 1965)., To all holders of MIL-STD-1234, the following pages of MIL-STD-1234 have been revised and supersede the pages listed.

MIL-STD-1234 (NOTICE 2), MILITARY STANDARD, PYROTECHNICS: SAMPLING INSPECTION AND TESTING (30 MAR 1967)., To all holders of MIL-STD-1234, the following pages of MIL-STD-1234 have been revised and the pages listed.

MIL-STD-1234 (NOTICE 3), MILITARY STANDARD, PYROTECHNICS: SAMPLING INSPECTION AND TESTING (28 MAY 1973)., To all holders of MIL-STD-1234, the following pages of MIL-STD-1234 have been revised and the pages listed.

MIL-STD-1234, MILITARY STANDARD, PYROTECHNICS: SAMPLING, INSPECTION AND TESTING (22 JUN 1962)., This standard describes the general methods of sampling, inspecting, and testing pyrotechnics for conformance with the material requirements of the applicable pyrotechnic specification. In the event of conflict between these methods and those in the applicable pyrotechnic specification, the latter shall take precedence.

MIL-STD-1235C (NOTICE 1), MILITARY STANDARD, SINGLE AND MULTILEVEL CONTINUOUS SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES (16 APR 1997)., MIL-STD-1235C, dated 15 March 1988, is hereby canceled without replacement.

MIL-STD-1235C, MILITARY STANDARD, SINGLE- AND MULTI-LEVEL CONTINUOUS SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES, FUNCTIONAL CURVES OF THE CONTINUOUS SAMPLING PLANS (15 MAR 1988)., This standard establishes continuous sampling plans and procedures for inspection by attributes. In addition this standard provides functional curves of the continuous sampling plans (with the exception of the CSP-F plans) as well as a description of their use and guidelines for interpretation.

MIL-STD-1241A (NOTICE 1), MILITARY STANDARD, OPTICAL TERMS AND DEFINITIONS (15 MAY 1987)., MIL-STD-1241A, dated 31 March 1967, has been reviewed and determined valid for use in acquisition.

MIL-STD-1241A, MILITARY STANDARD, OPTICAL TERMS AND DEFINITIONS (31 MAR 1967)., This standard establishes definitions for the words, terms, and expressions peculiar to the general field of optics.

MIL-STD-1246C (NOTICE 1), MILITARY STANDARD, PRODUCT CLEANLINESS LEVELS AND CONTAMINATION CONTROL PROGRAM (16 MAY 1994) [S/S BY IEST-STD-CC1245D]., To all holders of MIL-STD-1246C, the following page of MIL-STD-1246C has been corrected and supersedes the page listed.

MIL-STD-1246C (NOTICE 2), MILITARY STANDARD, PRODUCT CLEANLINESS LEVELS AND CONTAMINATION CONTROL PROGRAM (15 DEC 1994)., To all holders of MIL-STD-1246C, the following page of MIL-STD-1246C has been corrected and supersedes the page listed.

MIL-STD-1246C (NOTICE 3), MILITARY STANDARD, PRODUCT CLEANLINESS LEVELS AND CONTAMINATION CONTROL PROGRAM (15 JUN 1998) [S/S BY IEST-STD-CC1245D]., MIL-STD-1246C, dated 11 April 1994, and any subsequent revisions and change notices are inactive for new design and shall no longer be used as a reference for new design.

MIL-STD-1246C (NOTICE 4), MILITARY STANDARD, PRODUCT CLEANLINESS LEVELS AND CONTAMINATION CONTROL PROGRAM (15 FEB 2002) [S/S BY IEST-STD-CC1245D]. MIL-STD-1246C, dated 15 June 1998, is hereby canceled.MIL-STD-1246C (NOTICE 3), MILITARY STANDARD, PRODUCT CLEANLINESS LEVELS AND CONTAMINATION CONTROL PROGRAM (15 FEB 2002)

MIL-STD-1246C, MILITARY STANDARD, PRODUCT CLEANLINESS LEVELS CONTAMINATION CONTROL PROGRAM (11 APR 1994) [S/S BY IEST-STD-CC1245D]. This standard provides a basis and a uniform method for specifying product cleanliness levels and contamination control program requirements.

MIL-STD-1247C, MILITARY STANDARD, MARKING, FUNCTIONS, AND HAZARD DESIGNATIONS OF HOSE, PIPE, AND TUBE LINES FOR AIRCRAFT MISSILE, AND SPACE SYSTEMS (13 OCT 1989)., This standard establishes material, labeling requirements for identification, function, subfunction, pressures, hazards and direction of lfow for pipes, hoses and tube liens used in aircraft, missile, space systems, and support equipment. The use of colors, words and symbols to identify the functions of such items (to include approved abbreviations), and the dimensions of labeling items such as tags, tapes, and bands, are specifically prescribed (see 4.1.1).

MIL-STD-1249A (NOTICE 1), MILITARY STANDARD, PROCEDURES FOR THE FUNCTIONAL CATEGORIZATION OF MISSILE ELECTRICAL AND ELECTRONIC TEST FUNCTION ITEMS (8 APR 1996)., MIL-STD-1249A, dated 12 April 1993, is hereby canceled without replacement.

MIL-STD-1249A, MILITARY STANDARD, PROCEDURES FOR THE FUNCTIONAL CATEGORIZATION OF GUIDED MISSILE ELECTRICAL AND ELECTRONIC TEST FUNCTION TERMS (12 APR 1993)., The scope of the categorization procedures contained in this military standard covers the functional classification of the inherent electrical or electronic test function capabilities of an item and the delineation of its pertinent characteristics. The technical data resulting from these categorization procedures will provide the government with the documentation necessary to revise MIL-HDBK-142 to reflect technological advances and changes in military requirements for this type of equipment.

MIL-STD-1250, MILITARY STANDARD, CORROSION PREVENTION AND DETERIORATION CONTROL IN ELECTRONIC COMPONENTS AND ASSEMBLIES (31 MAR 1967)., This standard serves as a guide and establishes minimum requirements for procedures, materials and systems for protecting electronic components and assemblies from adverse environments. Protective measures shall be sufficient to maintain performance characteristics within specified limits both during and after exposure to moisture, high and low temperature, corrosive gases, chemicals, and microbial attack. This standard does not deal with protection against damage from stress, shock, or vibration. It is not concerned with electrical or mechanical design except insofar as design details affect susceptibility to corrosion. Provisions for prevention of deterioration shall apply to housings, chassis, hardware, and similar parts which are assembled into electronic equipment, as well as to electronic and electro-mechanical components. Unless specifically mentioned in the item specification or drawing, this standard does not apply to standard commercial equipment.

MIL-STD-1250A (NOTICE 1), MILITARY STANDARD, CORROSION PREVENTION AND DETERIORATION CONTROL IN ELECTRONIC COMPONENTS AND ASSEMBLIES (18 AUG 1995)., MIL-STD-1250A, dated 29 June 1992, is hereby canceled. Future acquisitions should refer to MIL-HDBK-1250, Corrosion Prevention and Deterioration Control In Electronic Components and Assemblies.

MIL-STD-1250A, MILITARY STANDARD, CORROSION PREVENTION AND DETERIORATION CONTROL IN ELECTRONIC COMPONENTS AND ASSEMBLIES (29 JUN 1992)., This standard establishes minimum requirements for procedures, materials and systems for protecting electronic components in DoD systems and assemblies from adverse environments. Protective measures shall be sufficient to maintain performance characteristics within specified limits both during and after exposure to moisture, high and low temperatures, corrosive gases, chemicals and microbial (fungal) attack. This standard does not deal with protection against damage from stress, shock, vibration or nuclear, biological and chemical (NBC) contamination.

MIL-STD-1251A (NOTICE 1), MILITARY STANDARD SCREWS AND BOLTS PREFERRED FOR DESIGN LISTING OF (2 APR 1995)., MIL– STD– 1251 A, dated 15 September 1981, is hereby canceled without replacement.

MIL-STD-1251A, MILITARY STANDARD, SCREWS AND BOLTS PREFERRED FOR DESIGN LISTING OF (15 SEPT 1981)., The purpose of this bookform standard is to provide a commodity type parts document on screws and bolts to aid military equipment designers and engineers in the selection of preferred screws and bolts.

MIL-STD-1252 (NOTICE 1), MILITARY STANDARD, INERTIA FRICTION WELDING PROCESS, PROCEDURE, AND PERFORMANCE QUALIFICATION (11 MAR 1998)., MIL-STD-1252, dated 30 June 1975, and any subsequent revisions or change notices are inactive for new design and shall be no longer used as a guidance reference for new designs.

MIL-STD-1252, MILITARY STANDARD, INERTIA FRICTION WELDING PROCESS, PROCEDURE, AND PERFORMANCE QUALIFICATION (30 JUN 1975)., This standard contains design requirements and design consideration for the use of inertia friction welding. cation of welding procedures, and qualification of operators using these procedures and equipm

MIL-STD-1258 (NOTICE 1), MILITARY STANDARD, CHROMIUM PLATED 5.56MM, 7.62MM, AND CALIBER .30 SMALL ARMS BARREL BORES (28 MAY 1987)., MIL-STD-1258(AR), dated 30 June 1972, has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1258, MILITARY STANDARD, COMPARISON STANDARDS FOR CHROMIUM PLATED 5.56MM, 7.62MM, AND CALIBER .30 SMALL ARMS BARREL BORES (30 JUN 1972) [S/S SA-STD-102]., This document establishes visual comparison standards for workmanship type defects in chromium plated 5.56MM, 7.62MM, AND CALIBER .30 SMALL ARMS BARREL BORES

MIL-STD-1261C (NOTICE 1), MILITARY STANDARD, ARC WELDING PROCEDURES FOR CONSTRUCTIONAL STEEL (5 FEB 1991) [S/S BY TACOM DRAWING 12479550]., To all holders of MIL-STD-1261C, the following pages of MIL-STD-1261C have been revised and supersede the pages listed.

MIL-STD-1261C (NOTICE 3), MILITARY STANDARD, ARC WELDING PROCEDURES FOR CONSTRUCTIONAL STEELS (13 MAY 1998)[S/S BY TACOM DRAWING 12479550]., MIL STD-1261C, dated 31 May 1985, is hereby reinstated and may be used for acquisition.

MIL-STD-1261C (NOTICE 4), MILITARY STANDARD, ARC WELDING PROCEDURES FOR CONSTRUCTIONAL STEELS (14 MAY 1998) [S/S BY TACOM DRAWING 12479550]. This notice should be filed in front of MIL-STD-1261C, dated 31 May 1985. MIL-STD-1261C is inactive for new design and is no longer used as a guidance reference for new designs.

MIL-STD-1261C (NOTICE 5), MILITARY STANDARD, ARC WELDING PROCEDURES FOR CONSTRUCTIONAL STEELS (28 JUL 2003) [S/S BY TACOM DRAWING 12479550]., MIL-STD-1261C, dated 31 May 1985, is hereby cancelled. Future acquisitions should refer to TACOM Drawing 12479550, “Arc Welding Procedures For Constructional Steels”.

MIL-STD-1261C, MILITARY STANDARD, ARC WELDING PROCEDURES FOR CONSTRUCTIONAL STEELS (20 JAN 1988) [S/S BY TACOM DRAWING 12479550]., This standard covers the classification of metal-arc welding of constructional steels and the procedures required for documentation before production welding.

MIL-STD-1262 (NOTICE 1), MILITARY STANDARD, DEGRADATION TESTS FOR FUELS AND FUEL CONTAINER COATINGS (TEST PROCEDURE) (25 JUN 1992)., Standard MIL-STD-1262, dated 13 August 1967 is hereby canceled without replacement.

MIL-STD-1262, MILITARY STANDARD, DEGRADATION TESTS FOR FUELS AND FUEL CONTAINER COATINGS (TEST PROCEDURE) (31 AUG 1967)., This standard establishes the requirements and test methods for determining the compatibility of protective coatings intended for lining the interior surfaces of bulk transportation and storage containers with military petroleum base hydrocarbon fuels.

MIL-STD-1264B (NOTICE 1), MILITARY STANDARD, RADIOGRAPHIC INSPECTION FOR SOUNDNESS OF WELDS IN STEEL BY COMPARISON TO GRADED ASTM E390 REFERENCE RADIOGRAPHS (26 JUL 1993) [S/S BY MIL-HDBK-1264]., MIL-STD-1264B, dated 18 January 1989, has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1264B (NOTICE 2), MILITARY STANDARD, RADIOGRAPHIC INSPECTION FOR SOUNDNESS OF WELDS IN STEEL BY COMPARISON TO GRADED ASTM E390 REFERENCE RADIOGRAPHS (17 AUG 1998) [S/S BY MIL-HDBK-1264]., MIL-STD-1264B, dated 18 January 1989, is hereby canceled and superseded by MIL-HDBK-1264, dated 17 August 1998.

MIL-STD-1264B, MILITARY STANDARD, RADIOGRAPHIC INSPECTION FOR SOUNDNESS OF WELDS IN STEEL BY COMPARISON TO GRADED ASTM E390 REFERENCE RADIOGRAPHS (18 JAN 1989) [S/S BY MIL-HDBK-1264]., This standard prescribes requirements for radiographic inspection for soundness of welds in steel by comparison to selected severity levels of ASTM 390 reference radiographs. The base material varies from greater than .25 to 3 in (6.4 - 76 mm) inclusive in thickness. Volume 11 is applicable. This standard is not suitable for shipyard use.

MIL-STD-1265A (NOTICE 1), MILITARY STANDARD RADIOGRAPHIC INSPECTION, CLASSIFICATION, AND SOUNDNESS REQUIREMENTS FOR STEEL CASTINGS (2 JUL 1992) [S/S BY MIL-HDBK-1265]. MIL-STD-1265A, dated 28 May 1987, has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1265A (NOTICE 2), MILITARY STANDARD, RADIOGRAPHIC INSPECTION, CLASSIFICATION AND SOUNDNESS REQUIREMENTS FOR STEEL CASTINGS (19 AUG 1998) [S/S BY MIL-HDBK-1265]., MIL-STD-1265A(MR), dated 28 May 1987, is hereby canceled superseded by MIL-HDBK-1265, dated 19 August 1998.

MIL-STD-1265A, MILITARY STANDARD, RADIOGRAPHIC INSPECTION, CLASSIFICATION AND SOUNDNESS REQUIREMENTS FOR STEEL CASTINGS (29 MAY 1987) [S/S BY MIL-HDBK-1265]. This standard prescribes the requirements for the classification and soundness of steel castings exclusive of weld repair. This standard supplements detail casting specifications when specified.

MIL-STD-1267 (NOTICE 1), MILITARY STANDARD, DIMENSIONING OF BARREL CHAMBERS AND SMALL ARMS WEAPONS (16 APR 1986)., This notice should be filed in front of MIL-STD-1267 dated 28 July 1961. MIL-STD-1267 has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1267 (NOTICE 2), MILITARY STANDARD, DIMENSIONING OF BARREL CHAMBERS AND SMALL ARMS WEAPONS (12 JUL 1995)., MIL-STD-1267, DATED 28 July 1961, IS HEREBY CANCELED WITHOUT REPLACEMENT.

MIL-STD-1267, MILITARY STANDARD, DIMENSIONING OF BARREL CHAMBERS AND SMALL ARMS WEAPONS (28 JUL 1961). This document establishes standard methods of dimensioning barrel chambers for small arms weapons on detailed drawings for each type of barrel chamber described herein. It also establishes standard methods for specifying headspace dimensions for the assembled weapon.

MIL-STD-1270A (NOTICE 1), MILITARY STANDARD, PATCHING OF WOOD STOCKS FOR THE 7.62MM, M14, AND M14E2 RIFLES (26 AUG 1966)., To all holders of MIL-STD-1270A (WC) 1. MIL-STD–1270A (WC), 18 March 1966 is changed as follows:2. Remove old pages and insert new pages as indicated below.

MIL-STD-1270A (NOTICE 2), MILITARY STANDARD, PATCHING OF WOOD STOCKS FOR THE 7.62MM, M14 AND M14E2 RIFLES (16 APR 1986)., This notice should be filed in front of MIL-STD-1270A(AR), dated 18 March 1966. MIL–STD-1270A(AR) has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1270A, MILITARY STANDARD, PATCHING OF WOOD STOCKS FOR THE 7.62 MM, M14 AND M14E2 RIFLES (18 MAR 1966)., This document establishes standard materials and procedures for patching of wood stocks for the 7.62 MM, M14, and M14E2 rifles, and limits the size and location of defects which may be repaired by teh application of wood patches and plastic fillers.

MIL-STD-1274 (NOTICE 1), MILITARY STANDARD, MOTORCYCLE, MOTOR SCOOTER AND BICYCLE, STANDARD MODELS AND SPECIAL EQUIPMENT REQUIREMENTS (5 MAR 1982)., MIL-STD-1274, dated 2 March 1965, is hereby cancelled without replacement.

MIL-STD-1275A (NOTICE 1), MILITARY STANDARD, CHARACTERISTICS OF 28 VOLT DC ELECTRICAL SYSTEMS IN MILITARY VEHICLES (8 FEB 1980)., To al1 holders of MIL-STD-1 275A: 1. The following pen and ink change shall be made: PAGE 7 Add herein "NATO-STANAG 2601” to the international standardization agreement note.

MIL-STD-1275A (NOTICE 2), MILITARY STANDARD, CHARACTERISTICS OF 28 VOLT DC ELECTRICAL SYSTEMS IN MILITARY VEHICLES(23 APR 1981)., To all holders of MIL-STD-1275A(AT): 1. THE FOLLOWING PEN AND INK CHANGE SHALL BE MADE: PACE 4 5.2.1, delete and substitute: "5.2.1 Steady-state voltage. The voltage shall be greater than 23 volts and less than 33 volts.”

MIL-STD-1275A, MILITARY STANDARD, CHARACTERISTICS OF 28 VOLT DC ELECTRICAL SYSTEMS IN MILITARY VEHICLES (17 SEPT 1976). This standard covers the limits of transient voltage characteristics and steady state limits of the 28 volt (V) direct current (dc) electric power circuits of military vehicles.

MIL-STD-1275B, MILITARY STANDARD, CHARACTERISTICS OF 28 VOLT DC ELECTRICAL SYSTEMS IN MILITARY VEHICLES (20 NOV 1997)., This standard covers the limits of transient voltage characteristics and steady state limits of the 28 volt (V) direct current (dc) electric power circuits of military vehicles.

MIL-STD-1275D, MILITARY STANDARD, CHARACTERISTICS OF 28 VOLT DC ELECTRICAL SYSTEMS IN MILITARY VEHICLES (29 AUG 2006)., This standard covers the limits of transient voltage characteristics and steady state limits of the 28 volt (V) direct current (dc) electric power circuits of military vehicles.

MIL-STD-1276E, MILITARY STANDARD, LEADS FOR ELECTRONIC COMPONENT PART (18 MAY 1993)., This standard establishes the method of identifying, specifying, and limiting to a minimum the combinations of basic materials, the thickness and composition of the plating used therewith, and the sizes for wire and flat wire (ribbon) leads on electronic and electrical parts when they are to be soldered or welded during assembly in equipment.

MIL-STD-1276F, MILITARY STANDARD, LEADS FOR ELECTRONIC COMPONENT PARTS (14 JAN 2000)., This standard establishes the method of identifying, specifying, and limiting to a minimum the combinations of basic materials, the thickness and composition of the plating used therewith, and the sizes of wire and flat wire (ribbon) leads on electronic and electrical parts when they are to be soldered or welded during assembly in equipment.

MIL-STD-1276G, MILITARY STANDARD, LEADS FOR ELECTRONIC COMPONENT PARTS (14 MAR 2005)., This standard establishes the method of identifying, specifying, and limiting to a minimum the combinations of basic materials, the thickness and composition of the plating used therewith, and the sizes of wire and flat wire (ribbon) leads on electronic and electrical parts when they are to be soldered or welded during assembly in equipment.

MIL-STD-1277B (NOTICE 1), MILITARY STANDARD, SPLICES, TERMINALS, TERMINAL BOARDS, BINDING POSTS, TERMINAL JUNCTION SYSTEMS, WIRE CAPS; ELECTRICAL (20 FEB 1998)., MIL-STD-1277B, dated 28 December 1983, is hereby canceled.

MIL-STD-1277B, MILITARY STANDARD, SPLICES, TERMINALS, TERMINAL BOARDS, BINDING POSTS, TERMINAL JUNCTION SYSTEMS, WIRE CAPS; ELECTRICAL (28 DEC 1983)., This standard establishes a list for the selection of splices, terminals, terminal boards, binding posts, terminal junction systems, and wire caps designated as preferred for use in new design of military equipment. Complete detail requirements for splices, terminals, terminal boards, binding posts, terminal junction systems and wire caps listed in this standard are covered in the applicable military document listed herein.

MIL-STD-1278 (NOTICE 1), MILITARY STANDARD, FILTERS LIGHT PHOTOGRAPHIC (23 MAY 1986). MIL-STD-1278, dated 20 October 1966, is hereby validated and determined to be adequate for acquisition.

MIL-STD-1278 (NOTICE 2), MILITARY STANDARD, FILTERS LIGHT PHOTOGRAPHIC (14 JUN 1993)., MIL-STD-1278, dated 20 October 1966, is hereby validated and determined to be adequate for acquisition.

MIL-STD-1278 (NOTICE 3), MILITARY STANDARD, FILTERS, LIGHT, PHOTOGRAPHIC (5 DEC 1995). MIL-STD-1278, dated 20 October 1966, is hereby canceled without replacement.

MIL-STD-1278, MILITARY STANDARD, FILTERS, LIGHTS, PHOTOGRAPHIC (20 OCT 1966)., This standard is issued to describe a general method of describing filters according to construction type, optical quality, and intended use, and to establish uniform definitions, general requirements (which includes the military filter designation system), detailed requirements, and test methods for filters used in military photographic work.

MIL-STD-1279 (NOTICE 1), MILITARY STANDARD, METERS, ELECTRICAL INDICATING SELECTION AND USE OF (21 DEC 1971)., To all holders of MIL-STD-1279, the following pages of MIL-STD-1279 have been revised and supersede the pages listed.

MIL-STD-1279 (NOTICE 2), MILITARY STANDARD, METERS, ELECTRICAL INDICATING SELECTION AND USE OF (2 APR 1986)., MIL-STD-1279, dated 10 September 1970, has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1279 (NOTICE 3), MILITARY STANDARD, METERS, ELECTRICAL INDICATING SELECTION AND USE OF (13 SEPT 1999)., This notice should be filed in front of MIL-STD-1279, dated 10 September 1970. MIL-STD-1279, dated 10 September 1970, is hereby canceled without replacement.

MIL-STD-1279, MILITARY STANDARD, METERS, ELECTRICAL INDICATING SELECTION AND USE OF (10 SEPT 1970)., This standard consists of the following -selected standard electrical indicating meter types, detailed by sections, chosen jointly by the Departments of the Army, the Navy, and the Air Force for use in new design and manufacture of military equipment under the jurisdiction of the departments; guides for the choice and application of electrical indicating meters in military equipment. Detailed requirements of these meters are covered in the latest issue fo the applicable specification.

MIL-STD-1280 (NOTICE 1), MILITARY STANDARD, KEYBOARD ARRANGEMENTS (8 JUN 1988) [S/S BY MIL-HDBK-1280]., To all holders of MIL-STD-1280: the following pages of MIL-STD-1280 have been revised and supersede the pages listed.

MIL-STD-1280 (NOTICE 2), MILITARY STANDARD, KEYBOARD ARRANGEMENTS (20 FEB 1998) [S/S BY MIL-HDBK-1280]., MIL-STD-1280, dated 28 January 1969, is hereby canceled. Future acquisitions should refer to MIL-HDBK-1280, Handbook for Keyboard Arrangements.

MIL-STD-1280, MILITARY STANDARD, KEYBOARD ARRANGEMENTS (28 JAN 1969) [S/S BY MIL-HDBK-1280]. This standard establishes the assignment of the 128 characters of the military standard code for information interchange and 54 of the 57 "American" characters of USASCSOCR X3.17-1966 to keys in a typewriter-like keyboard arrangement for application where the textual information has a high alpha content. This standard also establishes the assignment of the same character sets in a typewriter-like keyboard arrangement for application where the textual information usually has a high numeric content.

MIL-STD-1281, MILITARY STANDARD, INTERNAL TRANSIENT CONTROL FOR SOLID STATE POWER SUPPLIES (10 OCT 1968). This standard covers the requirements and test limits for the determination, measurement, and control of internal transients of solid state power supplies.

MIL-STD-1285B, MILITARY STANDARD, MARKING OF ELECTRICAL AND ELECTRONIC PARTS (2 APR 1990)., This standard establishes requirements for the physical marking of electrical and electronic parts. This standard should be implemented by incorporating suitable requirements directly in acquisition documents.

MIL-STD-1285C (NOTICE 1), MILITARY STANDARD, MARKING OF ELECTRICAL AND ELECTRONIC PARTS (22 AUG 2003),. THE FOLLOWING PAGES OF MIL-STD-1285C HAVE BEEN REVISED AND SUPERSEDE THE PAGES LISTED:

MIL-STD-1285C, MILITARY STANDARD, MARKING OF ELECTRICAL AND ELECTRONIC PARTS (27 SEPT 1999)., This standard establishes requirements for the physical marking of electrical and electronic parts. This standard should be implemented by incorporating suitable requirements directly in acquisition documents.

MIL-STD-1285D, MILITARY STANDARD, MARKING OF ELECTRICAL AND ELECTRONIC PARTS (7 SEPT 2004)., This standard establishes requirements for the physical marking of electrical and electronic parts. This standard should be implemented by incorporating suitable requirements directly in acquisition documents.

MIL-STD-1289B, MILITARY STANDARD, AIRBORNE STORES GROUND FIT AND COMPATIBILITY, REQUIREMENTS FOR (5 NOV 1990)., This standard establishes the requirements and testing procedures installation of all munitions and stores carried on an aircraft.

MIL-STD-1289C (NOTICE 2). MILITARY STANDARD, AIRBORNE STORES GROUND FIT & COMPATIBILITY, REQUIREMENTS FOR (24 JUL 2002)., MIL-STD-1289C, which was cancelled on 5 December 1995, is hereby reinstated. Since the current document is outdated, it shall not be used for acquisition until it’s revised and converted to a Standard Practice. The revision is underway with assigned project number SESS-0032-000 and an estimated completion of FY 3/03.

MIL-STD-1289C, MILITARY STANDARD, AIRBORNE STORES, GROUND FIT AND COMPATIBILITY REQUIREMENTS (17 JAN 1995)., This standard establishes the requirements and testing procedures for installations of all munitions and stores carried on an aircraft. It includes testing of all stores defined in 3.2

MIL-STD-1289D, MILITARY STANDARD, AIRBORNE STORES GROUND FIT AND COMPATIBILITY, REQUIREMENTS (24 SEPT 2003)., This standard establishes the requirements and testing procedures for installations of all munitions and stores carried on an aircraft. It includes testing of all stores defined in 3.2.

MIL-STD-1290A (NOTICE 1), MILITARY STANDARD, LIGHT FIXED & ROTARY-WING AIRCRAFT CRASH RESISTANCE (5 DEC 1995)., MIL-STD-1290A dated 26 September 1988, is hereby canceled without replacement.

MIL-STD-1290A, MILITARY STANDARD, LIGHT FIXED AND ROTARY WING AIRCRAFT CRASH RESISTANCE (26 SEPT 1988)., This document establishes minimum crash resistance criteria for implementation in the initial stages of aircraft system design.

MIL-STD-1291A (NOTICE 1), MILITARY STANDARD, IDENTIFICATION SYMBOLS FOR AEROSPACE FASTENER MANUFACTURES (13 MAY 1991) [S/S BY MIL-HDBK-57]., MIL-STD-1291A, dated 16 Jan 1984 is hereby cancelled and superseded by MIL-HDBK-57, l,LISTING OF FASTENER MANUFACTURES IDENTIFICATION SYMBOLS".

MIL-STD-1291A, MILITARY STANDARD, IDENTIFICATION SYMBOLS FOR AEROSPACE FASTENER MANUFACTURERS (16 JAN 1984) [S/S BY MIL-HDBK-57]., This document is a directory of Aerospace fastener Manufacturers Identification Symbols or Markings which they use to identify their products, their Federal Supply Code for Manufacturers (FSCM) No. and last known address and telephone number.

MIL-STD-1293 (NOTICE 1), MILITARY STANDARD, ELECTRO-MECHANICAL COMMAND INSTRUMENT SYSTEM FOR ROTARY WING AIRCRAFT (16 APR 1986)., MIL-STD-1293, dated 26 Sep 1979, has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1293 (NOTICE 2), MILITARY STANDARD, ELECTRO-MECHANICAL COMMAND INSTRUMENT SYSTEM FOR ROTARY WING AIRCRAFT (5 DEC 1995)., MIL-STD- 1293 dated 26 September 1979, is hereby canceled without replacement.

MIL-STD-1293, MILITARY STANDARD, ELECTRO-MECHANICAL COMMAND INSTRUMENT SYSTEM FOR ROTARY WING AIRCRAFT (26 SEPT 1979)., The purpose of this standard is to establish design requirements for Electro-Mechanical Command Instrument Systems (Flight Directors) for Rotary Wing aircraft.

MIL-STD-1294A (NOTICE 1), MILITARY STANDARD, ACOUSTICAL NOISE LIMITS IN HELICOPTERS (5 DEC 1995)., MIL_STD-1294 dated 12 AUG 1985, is hereby canceled w/o replacement.

MIL-STD-1294A, MILITARY STANDARD, ACOUSTICAL NOISE LIMITS IN HELICOPTERS (12 AUG 1985)., This standard establishes steady state acoustical noise limits within personnel occupied spaces of military helicopters.

MIL-STD-1295A (NOTICE 1), MILITARY STANDARD, HUMAN FACTORS ENGINEERING DESIGN CRITERIA FOR HELICOPTER COCKPIT ELECTRO-OPTICAL DISPLAY SYMBOLOGY (18 MAY 1996). MIL-STD-1259A, dated 26 June 1984, is hereby canceled without replacement.

MIL-STD-1295A, MILITARY STANDARD, HUMAN FACTORS ENGINEERING DESIGN CRITERIA FOR HELICOPTER COCKPIT ELECTRO-OPTICAL DISPLAY SYMBOLOGY (26 JUN 1984)., The purpose of this standard is to establish human factors criteria for symbolic and alphanumeric information used on electronically optically generated airborne displays. Electronically and optically generated displays are those in which an image is presented to the observer directly on the image-generating surface or indirectly through an optical projection system.