MIL SPECS (MIL-DTL)

Ident. Num:
MIL-DTL-001298 
  Rev. Num:

MIL-DTL-001298D (w/ AMENDMENT 1), MILITARY SPECIFICATION GUN, MACHINE; CALIBER .50, BROWNING, M2, HEAVY BARREL (24 MAR 2008)., This specification is approved for interim use by the U.S. Army Armaments Research, Development and Engineering Center (ARDEC). Other activities in the Department of Defense may use this interim revision or may continue using MIL-G-1298A. This detail specification prescribes the requirements and identifies the verification procedures for the gun, machine, caliber .50, browning, M2, heavy barrel, hereafter referred to simply as the M2.
Ident. Num:
MIL-DTL-0053022 
  Rev. Num:

MIL-DTL-0053022C (MR), DETAIL SPECIFICATION PRIMER, EPOXY COATING, CORROSION INHIBITING LEAD AND CHROMATE FREE (25 JAN 2007) [USED IN LIEU OF MIL-P-53022B]., This specification is approved for interim use by the U.S. Army Research Laboratory. Other activities in the Department of Defense may use this interim revision or may continue using MIL-P-53022B. This specification covers a flash drying, corrosion inhibiting epoxy primer for ferrous and nonferrous metals. The primer is lead and chromate free and meets the air pollution requirements for solvent emissions (see 1.2 and 6.1).
Ident. Num:
MIL-DTL-0053030 
  Rev. Num:

MIL-DTL-0053030B, DETAIL SPECIFICATION, PRIMER COATING, EPOXY, WATER REDUCIBLE, LEAD AND CHROMATE FREE (6 SEP 2006) [USED IN LIEU OF MIL-P-53030A]., This specification covers the requirements for a water-reducible, air-drying, corrosion-inhibiting, epoxy-type primer for pretreated ferrous and non-ferrous metals. The primer is lead and chromate-free and is compatible with chemical agent resistant aliphatic polyurethane topcoats. The primer contains no more than 340 grams per liter (2.8 pounds per gallon) of volatile organic compounds (VOC), as applied.
Ident. Num:
MIL-DTL-0070446 
  Rev. Num:

MIL-DTL-0070446B (w/AMENDMENT 1), DETAIL SPECIFICATION MACHINE GUN, 5.56MM: M249 (14 JUN 2007)., This specification is approved for interim use by the U.S. Army Armaments Research, Development and Engineering Center (ARDEC). Other activities in the Department of Defense may use this interim revision or may continue using MIL-M-70446A. This specification prescribes the detail requirements and identifies the verification procedures for the Machine Gun, 5.56MM: M249, hereafter referred to simply as the M249.
Ident. Num:
MIL-DTL-10176 
  Rev. Num:

MIL-DTL-10176K, MILITARY SPECIFICATION, CLOTH, GABARDINE: WOOL, POLYESTER AND WOOL (20 MAY 2005) [SUPERSEDING MIL-C-10176J]., This specification covers wool, polyester and wool gabardine cloths
Ident. Num:
MIL-DTL-10866 
  Rev. Num:

MIL-DTL-10866E, DETAIL SPECIFICATION, UREA, TECHNICAL (2 AUG 2005) [SUPERSEDING DOD-U-10866D]., This specification covers two classes of technical grade urea.
Ident. Num:
MIL-DTL-10884 
  Rev. Num:

MIL-DTL-10884H, DETAIL SPECIFICATION, FASTENERS, SNAP (20 JUL 2005) [SUPERSEDING MIL-F-10884G]., This specification covers metal snap fasteners intended for temporary joining of detachable components and parts of clothing, equipage and tentage items.
Ident. Num:
MIL-DTL-11015 
  Rev. Num:

MIL-DTL-11015/18E, MILITARY SPECIFICATION SHEET CAPACITORS, FIXED, CERAMIC DIELECTRIC (GENERAL PURPOSE), STYLE CK05 (14 May 2001) [SUPERSEDING MIL-C-11015/18D]., The requirements for acquiring the capacitors described herein shall consist of this specification and MIL-C-11015. This specification is approved for use by all Departments and Agencies of the Department of Defense. INACTIVE FOR NEW DESIGN after 28 September 1970.
Ident. Num:
MIL-DTL-11195 
  Rev. Num:

MIL-DTL-11195G, DETAIL SPECIFICATION, ENAMEL, LUSTERLESS, FAST DRY, VOC COMPLIANT, (FOR USE ON AMMUNITION AND OTHER METALS) (31 JUL 2003) [SUPERSEDING MIL-11195D]., This specification covers two types of fast drying, lusterless, low volatile organic compound (VOC) content alkyd enamels for use on exterior and interior metal surfaces. These enamels are formulated free of lead and chromate (hexavalent chromium), with a maximum VOC content of 420 g/L (3.5 lb/gal) as applied.
Ident. Num:
MIL-DTL-117 
  Rev. Num:

MIL-DTL-117H (w/AMENDMENT 1), DETAIL SPECIFICATION, BAGS, HEAT-SEALABLE (8 JUN 2007) [SUPERSEDING MIL-B-117G]., This document covers heat-sealable bags used in military preservation.
Ident. Num:
MIL-DTL-117 
  Rev. Num:

MIL-DTL-117H, DETAIL SPECIFICATION, BAGS, HEAT-SEALABLE (30 APR 2001) [SUPERSEDING MIL-B-117G]., This document covers heat-sealable bags used in military preservation.
Ident. Num:
MIL-DTL-1222 
  Rev. Num:

MIL-DTL-1222J, DETAIL SPECIFICATION STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; GENERAL SPECIFICATION FOR (8 DEC 2000) [SUPERSEDING MIL-S-1222H]., This specification is approved for use by all Departments and Agencies of the Department of Defense. 1 SCOPE 1.1 Scope. This specification covers standard studs, hex cap screws, and heavy hex bolts in nominal standard diameters of inch to 4 inches, nuts in nominal standard diameters of inch to 3 inches, and socket head cap screws in nominal standard diameters of inch to 1 inches for submarine safety and other applications where a high degree of reliability is required (see 6.1).
Ident. Num:
MIL-DTL-12468 
  Rev. Num:

MIL-DTL-12468D, DETAIL SPECIFICATION, DECONTAMINATING AGENT, STB (12 AUG 1998) [SUPERSEDING MIL-D-12468C]., This specification covers one type of decontaminating agent.
Ident. Num:
MIL-DTL-12883/54  
  Rev. Num:

MIL-DTL-12883/54, SOCKETS, PLUG-IN ELECTRONIC COMPONENTS SOCKET FOR MIL-PRF 6106 RELAYS AND MS27742 RELAYS (18 FED 2003)., MIL-DTL-12883/54A 18 February 2003 SUPERSEDING MIL-PRF-12883/54 24 January 1996 DETAIL SPECIFICATION SHEET SOCKETS, PLUG-IN ELECTRONIC COMPONENTS SOCKET FOR MIL-PRF 6106 RELAYS AND MS27742 RELAYS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-DTL-12883.
Ident. Num:
MIL-DTL-13074 
  Rev. Num:

MIL-DTL-13074B, DETAIL SPECIFICATION, WIRE, ELECTRICAL, ANTENNA, (WIRE W-27 AND WIRE WS-19( ) /U) (27 JUN 2003) [SUPERSEDING MIL-W-13074A (EL)]., This specification covers stranded, round electrical wire fabricated from silicon bronze, suitable for antenna applications.
Ident. Num:
MIL-DTL-13075 
  Rev. Num:

MIL-DTL-13075B, DETAIL SPECIFICATION, WIRE, ELECTRICAL (WIRE W-124, W-125, W-128) (14 JAN 2008) [SUPERSEDING MIL-W-13075]., This specification covers the following three types of No. 14 AWG Buna-S insulated wire used for antenna and ground connections: Wire W-124 Single Conductor (braided) Wire W-125 Two Parallel Conductors (common outer braid) Wire W-128 Single Conductor (without outer braid) 2.
Ident. Num:
MIL-DTL-13080 
  Rev. Num:

MIL-DTL-13080E, DETAIL SPECIFICATION ELECTRODES, WELDING, COVERED: AUSTENITIC STEEL (19-9 MODIFIED) FOR ARMOR APPLICATIONS (15 APR 1999) [SUPERSEDING MIL-E-13080D]., This specification covers austenitic steel arc welding electrodes for use on steels of high hardenability (see 6.1).
Ident. Num:
MIL-DTL-1318 
  Rev. Num:

MIL-DTL-1318C(AR), DETAIL SPECIFICATION, CARTRIDGE, CALIBER .50, TRACER, M17 (23 MAY 2007) {SUPERSEDING MIL-C-1318B(AR)]., This specification covers the requirements and verification methods for the Cartridge, Caliber .50, Tracer, M17.
Ident. Num:
MIL-DTL-13220 

MIL-DTL-13220/1, DETAIL SPECIFICATION SHEET GRAB HOOK, CLEVIS (25 SEP 2008)., This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-13220.
Ident. Num:
MIL-DTL-13220 

MIL-DTL-13220/3, DETAIL SPECIFICATION SHEET, GRAB HOOK, EYE (25 SEP 2008)., This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-13220.
Ident. Num:
MIL-DTL-13220 
  Rev. Num:

MIL-DTL-13220E (SUPPLEMENT 1), DETAIL SPECIFICATION, HOOK, SLIDING CHOKER (FOR USE WITH WIRE ROPE) (25 SEP 2008)., This supplement forms a part of MIL-DTL-13220E, dated 25 September 2008.
Ident. Num:
MIL-DTL-13486 
  Rev. Num:

MIL-DTL-13486E, DETAIL SPECIFICATION CABLES, SPECIAL PURPOSE, ELECTRICAL: LOW-TENSION, HEAVY-DUTY, SINGLE CONDUCTOR AND MULTIPLE CONDUCTOR, SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (8 MAY 2006) [SUPERSEDING MIL-C-13486]., This specification covers two types (shielded and unshielded) of insulated, heavy-duty, single and multiconductor, electrical cables for use in low-tension circuits (see 6.1).
Ident. Num:
MIL-DTL-13823 
  Rev. Num:

MIL-DTL-13823D, DETAIL SPECIFICATION, STEEL: SHAPES, ROLLED OR FORGED; BARS, FLATS AND SPECIAL SECTIONS (FOR ARMOR) (18 NOV 1998) [SUPERSEDING MIL-S-13823C]., This specification covers weldable steel bars, flats and special sections produced from billets to specified dimensions by rolling or forging, for armored vehicle components.
Ident. Num:
MIL-DTL-13924 
  Rev. Num:

MIL-DTL-13924D (NOTICE 1), DETAIL SPECIFICATION COATING, OXIDE, BLACK, FOR FERROUS METALS.MIL-DTL-13924D, dated 18 March 1999, has been reviewed and determined to be valid for use in acquisition
Ident. Num:
MIL-DTL-13924 
  Rev. Num:

MIL-DTL-13924D, DETAILED SPECIFICATION COATING, OXIDE, BLACK, FOR FERROUS METALS (18 MAR 1999) [SUPERSEDING MIL-C-13924C]., This specification covers black oxide coatings applied to ferrous metals (wrought iron, carbon, low alloy, and corrosion resistant steels). Black oxide coatings, with or without a supplementary preservative treatment, may be used where a black surface is required. Only very limited corrosion protection, under mildly corrosive conditions, is obtained as a result of black oxide coating.
Ident. Num:
MIL-DTL-1394  
  Rev. Num:

MIL-DTL-1394G, DETAIL SPECIFICATION, PRIMER, ELECTRIC: M52A3B1 (3 MAY 2006) [SUPERSEDING MIL-P-1394F(AR)]., This specification covers the electric primer M52A3B1, for use in the assembly of 20mm ammunition.
Ident. Num:
MIL-DTL-14072 
  Rev. Num:

MIL-DTL-14072E (CR), DETAIL SPECIFICATION FINISHES FOR GROUND BASED ELECTRONIC EQUIPMENT (31 MAY 2007) (SUPERSEDING MIL-F-14072D)., This specification covers requirements for finishes necessary to protect ground electronic equipment from the deteriorating effects of climatic conditions encountered in military use.
Ident. Num:
MIL-DTL-14538 
  Rev. Num:

MIL-DTL-14538D, DETAIL SPECIFICATION CHROMIUM PLATING, BLACK (ELECTRODEPOSITED) (16 JUN 1999)., This specification covers an electrodeposited black chromium finish. It is generally applied to steels but may be used as a plating for other metals such as brass, copper, iron and chromium (see 6.1, 6.3 and 6.4).
Ident. Num:
MIL-DTL-15024 
  Rev. Num:

MIL-DTL-15024F, DETAIL SPECIFICATION PLATES, TAGS, AND BANDS FOR IDENTIFICATION OF EQUIPMENT, GENERAL SPECIFICATION FOR (28 NOV 1997) (SUPERSEDING MIL-P-1502E)., This performance specification covers the physical characteristics of plates, tags and bands (identification devices) used for identification of equipment. Examples of information to be marked on the identification devices are covered in the applicable specification sheets.
Ident. Num:
MIL-DTL-15090 
  Rev. Num:

MIL-DTL-15090D, DETAIL SPECIFICATION ENAMEL, EQUIPMENT, LIGHT GRAY, (NAVY FORMULA NO. 111) (6 NOV 1996) [SUPERSEDING MIL-E-15090C]., This specification covers a 340 gram per liter (maximum) (2.8 pound per gallon [maximum]) volatile organic content (VOC) complying paint. The paint is a light gray equipment enamel (Navy Formula No. 111) for shipboard use as a topcoat on equipment, machinery, furniture and electrical equipment, such as switchboard installations. This product may be used wherever VOC air pollution regulations apply. The light gray equipment enamel covered by this specification is an air dry, solvent base coating for use in all interior dry areas including applications covered by reactor plant painting schedules (see 6.5).
Ident. Num:
MIL-DTL-15090 
  Rev. Num:

MIL-DTL-15090D, DETAIL SPECIFICATION, ENAMEL, EQUIPMENT, LIGHT GRAY, (NAVY FORMULA NO. 111) (6 NOV 1996) [SUPERSEDING MIL-E-15090C]., This specification covers a 340 gram per liter (maximum) (2.8 pound per gallon [maximum]) volatile organic content (VOC) complying paint. The paint is a light gray equipment enamel (Navy Formula No. 111) for shipboard use as a topcoat on equipment, machinery, furniture and electrical equipment, such as switchboard installations. This product may be used wherever VOC air pollution regulations apply. The light gray equipment enamel covered by this specification is an air dry, solvent base coating for use in all interior dry areas including applications covered by reactor plant painting schedules (see 6.5).
Ident. Num:
MIL-DTL-15562 
  Rev. Num:

MIL-DTL-15562G [NAVY), DETAIL SPECIFICATION, MATTING OR SHEET, FLOOR COVERING INSULATING FOR HIGH VOLTAGE APPLICATION (31 MAY 1996) [SUPERSEDING MIL-M-15562F]., This specification covers rubber or plastic matting and sheet floor coverings for use around electrical apparatus or circuits, as a safety measure to protect personnel from accidental exposure to electrical potentials not exceeding 3000 volts. Equipment operating at higher voltages utilize other built-in safety measures to provide personnel protection.
Ident. Num:
MIL-DTL-15562 
  Rev. Num:

MIL-DTL-15562G, DETAIL SPECIFICATION, MATTING OR SHEET, FLOOR COVERING, INSULATING FOR HIGH VOLTAGE APPLICATION (31 MAY 1996) (SUPERSEDING MIL-M-15562F)., This specification covers rubber or plastic matting and sheet floor coverings for use around electrical apparatus or circuits, as a safety measure to protect personnel from accidental exposure to electrical potentials not exceeding 3000 volts. Equipment operating at higher voltages utilize other built-in safety measures to provide personnel protection.
Ident. Num:
MIL-DTL-15659 
  Rev. Num:

MIL-DTL-15659J (SUPPLEMENT 1), DETAIL SPECIFICATION TERMINAL, LUG: SOLDER, COPPER AND PHOSPHOR BRONZE (15 DEC 2003) [SUPERSEDING MIL-T-15659H).
Ident. Num:
MIL-DTL-15659 
  Rev. Num:

MIL-DTL-15659J, DETAIL SPECIFICATION TERMINAL, LUG: SOLDER, COPPER AND PHOSPHOR BRONZE (15 DEC 2003) [SUPERSEDING MIL-T-15659H)., This specification covers copper and phosphor bronze or tin brass strip solder electrical lug terminals.
Ident. Num:
MIL-DTL-16036 
  Rev. Num:

MIL-DTL-16036L, DETAIL SPECIFICATION, SWITCHGEAR, POWER, LOW VOLTAGE, NAVAL SHIPBOARD (27 JAN 2006) [SUPERSEDING MIL-S-16036K]., This specification covers the requirements for electrical power dead-front, deck-mounted, low voltage switchgear for Naval shipboard use. Switchgear covered by this specification are of the following Types: a. Type I: Ships service power switchgear group for ships with alternating current (AC) power. b. Type II: Emergency switchgear group for ships with AC power. c. Type III: Ships service power switchgear group for ships with direct current (DC) power.
Ident. Num:
MIL-DTL-16232 
  Rev. Num:

MIL-DTL-16232G, DETAIL SPECIFICATION PHOSPHATE COATING, HEAVY, MANGANESE OR ZINC BASE (7 JAN 2000)., This specification covers two types of heavy phosphate coating for ferrous metals, applied by immersion. The coatings consist of a manganese phosphate or zinc phosphate base and, when specified, a supplementary treatment (see 6.1).
Ident. Num:
MIL-DTL-16232 
  Rev. Num:

MIL-DTL-16232G, DETAIL SPECIFICATION PHOSPHATE COATING, HEAVY, MANGANESE OR ZINC BASE (7 JAN 2000) [SUPERSEDING DOD-P-16232F AND MIL-P-16232E]., This specification covers two types of heavy phosphate coating for ferrous metals, applied by immersion. The coatings consist of a manganese phosphate or zinc phosphate base and, when specified, a supplementary treatment (see 6.1).
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H (SH) (SUPPLEMENT 1), DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (2 AUG 1996). This supplement forms a part of Military Specification MIL-DTL-16377H(SH), dated 2 August 1996.
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H (SH) (SUPPLEMENT 1A), DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (27 SEP 2004) [SUPERSEDING SUPPLEMENT 1]., This supplement forms a part of MIL-DTL-16377H(SH), dated 2 August 1996.
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H (SH) (SUPPLEMENT 1B), DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (27 SEP 2005) [SUPERSEDING SUPPLEMENT 1B]., This supplement forms a part of MIL-DTL-16377H(SH), dated 2 August 1996.
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H (SUPPLEMENT 1), DETAIL SPECIFICATION, FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (2 AUG 1996) [SUPERSEDING MIL-F-16377G (SH)]., This supplement forms a part of Military Specification MIL-DTL-16377H(SH), dated 2 August 1996.
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H (SUPPLEMENT 1A), DETAIL SPECIFICATION, FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (27 SEP 2004) [SUPERSEDING MIL-F-16377G (SH)]., This supplement forms a part of MIL-DTL-16377H (SH), dated 2 August 1996.
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H (SUPPLEMENT 1B), DETAIL SPECIFICATION, FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (27 SEP 2005) [SUPERSEDING MIL-F-16377G (SH)]., This supplement forms a part of MIL-DTL-16377H(SH), dated 2 August 1996.
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H, DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (2 AUG 1996) [SUPERSEDING MIL-F-16377G (SH)]., This specification covers fluorescent and incandescent lighting fixtures (lights) and associated parts. used for detail and general illumination on Naval ships and boats.
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H, DETAIL SPECIFICATION, FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (2 AUG 1996) [SUPERSEDING MIL-F-16377G (SH)]., This specification covers fluorescent and incandescent lighting fixtures (lights) and associated parts. used for detail and general illumination on Naval ships and boats.
Ident. Num:
MIL-DTL-16884 
  Rev. Num:

MIL-DTL-16884L, DETAIL SPECIFICATION FUEL, NAVAL DISTILLATE (23 OCT 2006) [SUPERSEDING MIL-PRF-16884K AND MIL-F-16884J]., This specification covers one grade of Naval distillate fuel: (NATO symbol F-76).
Ident. Num:
MIL-DTL-17667  
  Rev. Num:

MIL-DTL-17667E, DETAIL SPECIFICATION, PAPER, WRAPPING, CHEMICALLY NEUTRAL (NON-CORROSIVE) (21 APR 2005) [SUPERSEDING MIL-P-17667D]., This specification covers chemically neutral, non-corrosive wrapping paper used for packaging military supplies and equipment.
Ident. Num:
MIL-DTL-17901 
  Rev. Num:

MIL-DTL-17901C, DETAIL SPECIFICATION, BEARING COMPONENTS, BONDED SYNTHETIC RUBBER, WATER LUBRICATED (10 MAY 2005) [SUPERSEDING MIL-B-17901B(SH)]., This specification covers stave shaped and cylindrical shaped bearings that have synthetic rubber facings.
Ident. Num:
MIL-DTL-17 
  Rev. Num:

MIL-DTL-17H (SUPPLEMENT 1), DETAIL SPECIFICATION CABLES, RADIO FREQUENCY, FLEXIBLE AND SEMIRIGID, GENERAL SPECIFCATION FOR., This supplement forms a part of MIL-DTL-17H, dated 19 August 2005.
Ident. Num:
MIL-DTL-17 
  Rev. Num:

MIL-DTL-17H, DETAIL SPECIFICATION, CABLES, RADIO FREQUENCY, FLEXIBLE AND SEMIRIGID, GENERATION SPECIFICATION FOR (4 AUG 2006)., This supplement forms a part of MIL-DTL-17H, dated 19 August 2005.
Ident. Num:
MIL-DTL-18240 
  Rev. Num:

MIL-DTL-18240F (AMENDMENT 1), DETAIL SPECIFICATION FASTENER ELEMENT, SELF-LOCKING, THREADED FASTENER, 250F MAXIMUM (13 MAR 2000) [SUPERSEDING MIL-F-18240E).
Ident. Num:
MIL-DTL-18240 
  Rev. Num:

MIL-DTL-18240F, DETAIL SPECIFICATION FASTENER ELEMENT, SELF-LOCKING, THREADED FASTENER, 250F MAXIMUM (2 JUN 1997) [SUPERSEDING MIL-F-18240E)., This specification defines the requirements for self-locking elements for use in externally threaded fasteners such as bolts and screws to be used in fasteners with either UNC, UNJC, UNF, UNJF, UNRC or UNRF threads and where the temperatures will not exceed 250F.
Ident. Num:
MIL-DTL-18295 
  Rev. Num:

MIL-DTL-18295F, DETAIL SPECIFICATION, CHAINS AND FITTINGS FOR FLEET MOORING (30 JAN 1998) [SUPERSEDING MIL-C-18295E]., This specification establishes the requirements for the manufacture, physical performance, and acceptance of mooring chain assemblies. Mooring chain assemblies are to be subjected to long term submergence in seawater and may be subjected to open storage in a marine environment.
Ident. Num:
MIL-DTL-18307 
  Rev. Num:

MIL-DTL-18307H, DETAIL SPECIFICATION, NOMENCLATURE AND IDENTIFICATION FOR AERONAUTICAL SYSTEMS INCLUDING JOINT ELECTRONICS TYPE DESIGNATED SYSTEMS AND ASSOCIATED SUPPORT SYSTEMS (28 APR 2006) [SUPERSEDING MIL-N-18307 (NAVY)]., This specification establishes requirements for obtaining the official assignment or confirmation of nomenclature and for identification and re-identification marking for electronic and aeronautical equipment, including support equipment and systems; e.g., Test, Utility, Trainers, etc. Nomenclature procedures are explained in MIL-STD-196 for electronic equipment and MIL-HDBK-1812 for aeronautical, aeronautical support equipment, and photographic equipment.
Ident. Num:
MIL-DTL-18375 
  Rev. Num:

MIL-DTL-18375H, DETAIL SPECIFICATION, WIRE ROPE, FLEXIBLE, CORROSION-RESISTING, NONMAGNETIC, FOR AIRCRAFT CONTROL (1 APR 2005) [SUPERSEDING MIL-W-18375B]., This specification covers the requirements for nonmagnetic, corrosion resistant steel wire rope used in aircraft flight controls. The wire rope will be capable of operation within a -65 F to +250 F (-54 C to +121 C) temperature range in wind, dust, fuel and oil spills, in aircraft wash-down and other environmental stresses and aircraft experiences.
Ident. Num:
MIL-DTL-19491 
  Rev. Num:

MIL-DTL-19491H, DETAIL SPECIFICATION SEMICONDUCTOR DEVICES, PACKAGING OF (28 JUN 2002)., This specification covers the requirements for the preservation, packing, and container marking of semiconductor devices such as transistors and diodes (FSC 5961) (see 6.1).
Ident. Num:
MIL-DTL-197 
  Rev. Num:

MIL-DTL-197K (w/ AMENDMENT 1), DETAIL SPECIFICATION PACKAGING OF BEARINGS, ASSOCIATED PARTS AND SUBASSEMBLIES (11 OCT 2005)., This specification covers the cleaning, drying, preservation, packaging, and packaging marking requirements for all types and sizes of stock and production bearings, associated parts, and subassemblies (see 6.1).
Ident. Num:
MIL-DTL-197 
  Rev. Num:

MIL-DTL-197K (W/ AMENDMENT 1)., DETAIL SPECIFICATION PACKAGING OF BEARINGS, ASSOCIATED PARTS AND SUBASSEMBLIES (11 OCT 2005)., This specification covers the cleaning, drying, preservation, packaging, and packaging marking requirements for all types and sizes of stock and production bearings, associated parts, and subassemblies (see 6.1).
Ident. Num:
MIL-DTL-19834 
  Rev. Num:

MIL-DTL-19834C, DETAIL SPECIFICATION PLATES, IDENTIFICATION OR INSTRUCTION, METAL FOIL, ADHESIVE BACKED GENERAL SPECIFICATION FOR (6 JUL 2006) (SUPERSEDING MIL-P-19834B). This specification covers adhesive-backed metal foil identification or instruction plates, herein referred to as identification plates, for use as internal and external equipment identification or instruction (see 6.1).
Ident. Num:
MIL-DTL-20078  
  Rev. Num:

MIL-DTL-20078D, DETAIL SPECIFICATION, GASKET, FOR BALLISTIC DOORS AND HATCHES (10 SEP 2004) [SUPERSEDING MIL-G-20078C]., This specification establishes the requirements for metal inserted rubber gaskets and two -line rubber gaskets for ballistic doors and hatches (see 6.1).
Ident. Num:
MIL-DTL-21115 
  Rev. Num:

MIL-DTL-21115L, DETAIL SPECIFICATION, CLOTH, TROPICAL: WOOL, POLYESTER/WOOL (24 JUN 2005) [SUPERSEDING MIL-C-21115K)., This document covers wool and polyester/wool blend tropical cloths.
Ident. Num:
MIL-DTL-22342 
  Rev. Num:

MIL-DTL-22342E, DETAIL SPECIFICATION BROWS, ALUMINUM, BEAM AND TRUSS (7 JUL 1995) [SUPERSEDING MIL-B-22342D]., This specification covers aluminum beam and truss brows (ship's gangplanks).
Ident. Num:
MIL-DTL-22499 
  Rev. Num:

MIL-DTL-22499D, DETAIL SPECIFICATION, SHIM STOCK, LAMINATED (27 FEB 1998) [SUPERSEDING MIL-S-22499] [S/S BY SAE-AMS-DTL-22499]., This specification covers the requirements for surface bonded laminated shim stock
Ident. Num:
MIL-DTL-22520 
  Rev. Num:

MIL-DTL-22520G (SUPPLEMENT 1), DETAIL SPECIFICATION CRIMPING TOOLS, WIRE TERMINATION, GENERAL SPECIFICATION FOR (12 SEP 1997) [SUPERSEDING MIL-C-22520F].
Ident. Num:
MIL-DTL-22520 
  Rev. Num:

MIL-DTL-22520G, DETAIL SPECIFICATION CRIMPING TOOLS, WIRE TERMINATION, GENERAL SPECIFICATION FOR (12 SEP 1997) [SUPERSEDING MIL-C-22520F]., This specification covers the general requirements for crimping tools, accessories and inspection gages used for connecting removable contacts (such as; signal, power, coaxial, shielded, thermocouple, and filter pin contacts) coaxial connectors, shielded connectors, ferrules, terminals, end caps and splices to wire conductors for use in electric connectors, terminal junction systems, and other electric or electronic components. The crimping tools and accessories covered by this specification are for use by the military and are the only connector assembly devices to be qualified, procured and issued for military maintenance use.
Ident. Num:
MIL-DTL-22529 
  Rev. Num:

MIL-DTL-22529/1C, DETAIL SPECIFICATION SHEET GROMMET, COMPOSITE, EDGING (6 FEB 1998)., The requirements for acquiring the product described herein shall consist of this specification sheet and the issue of MIL-DTL-22529 listed in that issue of the Department of Defense Index of Specification and Standards (DoDISS) specified in the solicitation.
Ident. Num:
MIL-DTL-22529 
  Rev. Num:

MIL-DTL-22529/2B, DETAIL SPECIFICATION SHEET, GROMMET, CUSHION, COMPOSITE, EDGING (6 FEB 1998)., The requirements for acquiring the product described herein shall consist of this specification sheet and the issue of MIL-DTL-22529 listed in that issue of the Department of Defense Index of Specification and Standards (DoDISS) specified in the solicitation.
Ident. Num:
MIL-DTL-22529 
  Rev. Num:

MIL-DTL-22529D (AMENDMENT 2), DETAIL SPECIFICATION, GROMMET, EDGING (6 JUN 1996) [SUPERSEDING MIL-G-22529B].
Ident. Num:
MIL-DTL-22529 
  Rev. Num:

MIL-DTL-22529D, DETAIL SPECIFICATION, GROMMET, EDGING (6 JUN 1996) [SUPERSEDING MIL-G-22529B]., This specification covers three types of edging grommets; a plastic caterpillar style applied with an adhesive, and two spring-style, stainless steel based composite grommets requiring no adhesives. Edging grommets are used to provide abrasion protection of electrical current carrying wires and cable bundles routed through metal structures.
Ident. Num:
MIL-DTL-22992 
  Rev. Num:

MIL-DTL-22992F (w/AMENDMENT 1), DETAIL SPECIFICATION CONNECTORS, PLUGS AND RECEPTACLES, ELECTRICAL, WATERPROOF, QUICK DISCONNECT, HEAVY DUTY TYPE, GENERAL SPECIFICATION FOR (25 SEP 2005) [SUPERSEDING MIL-C-22992E]., This specification covers multi-contact, heavy duty, quick disconnect, waterproof, electrical plug and receptacle connectors and associated accessories for electronic and electrical power and control circuits. Connectors are rated for -55C to +125C (see 6.1).
Ident. Num:
MIL-DTL-22992 
  Rev. Num:

MIL-DTL-22992F (w/SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS, PLUGS AND RECEPTACLES, ELECTRICAL, WATERPROOF, QUICK DISCONNECT, HEAVY DUTY TYPE, GENERAL SPECIFICATION FOR (25 SEP 2005) [SUPERSEDING MIL-C-22992E].
Ident. Num:
MIL-DTL-23053 
  Rev. Num:

MIL-DTL-23053/4D, DETAIL SPECIFICATION SHEET INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, DUAL-WALL, OUTER WALL CROSSLINKED (17 JUN 1996) [SUPERSEDING MIL-I-23053/4C]., The requirements for acquiring the sleeving described herein shall consist of this specification sheet and the issue of the following specification listed in that issue of the Department of Defense Index of Specifications and standards (DODISS) specified in the solicitation: MIL-DTL-23053
Ident. Num:
MIL-DTL-23053 
  Rev. Num:

MIL-DTL-23053E (SUPPLEMENT 1), DETAIL SPECIFICATION, INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, GENERAL SPECIFICATION FOR (17 JUN 1996) [SUPERSEDING MIL-I-23053D]., This supplement forms a part of MIL-DTL-23053E, dated 17 June 1996.
Ident. Num:
MIL-DTL-23053 
  Rev. Num:

MIL-DTL-23053E (SUPPLEMENT 1A), DETAIL SPECIFICATION, INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, GENERAL SPECIFICATION FOR (21 OCT 1996) [SUPERSEDING MIL-I-23053D].,
Ident. Num:
MIL-DTL-23053 
  Rev. Num:

MIL-DTL-23053E, DETAIL SPECIFICATION, INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, GENERAL SPECIFICATION FOR (17 JUN 1996) [SUPERSEDING MIL-I-23053D]., This specification establishes the requirements for various types and colors of electrical insulating sleeving that will shrink to a predetermined size upon the application of heat. This specification includes provisions for demonstrating compliance with requirements through in process inspection and statistical process control (see 4.4.3.1). Continuous operating temperature ratings range from -80 to +250C (-112 to +482F) (see 6.1).
Ident. Num:
MIL-DTL-23549 
  Rev. Num:

MIL-DTL-23549D, DETAIL SPECIFICATION, GREASE, GENERAL PURPOSE (10 MAY 2002) [SUPERSEDING MIL-G-23549C]., This specification covers the requirements for one type and grade of a general purpose molybdenum disulfide grease for extended use at temperatures up to 177 C (350 F) and for brief periods of use at temperatures up to 204 C (400 F) (see 6.1).
Ident. Num:
MIL-DTL-23659 
  Rev. Num:

MIL-DTL-23659E, DETAIL SPECIFICATION, INITIATORS, ELECTRIC, GENERAL DESIGN SPECIFICATION FOR (27 SEP 2007) [SUPERSEDING MIL-I-23659B]., This specification furnishes general requirements for design and establishes uniform methods for testing electric initiators and electric initiator subassemblies. The purpose of the testing program is to determine the electric characteristics, soundness of mechanical design, output, and resistance to deleterious service environments. For purposes of this specification the term electric initiator includes items classified in FSC 1377 such as hot wire initiators, exploding bridgewire initiators, exploding foil initiators, conductive mix initiators, etc. Electric primers are not covered in this specification. All requirements for exploding foil initiators used in safety sensitive non-interrupted explosive train applications are contained in appendix A. Requirements for all other items are in the main body of this document. The term electric initiator does not include complete assemblies which have electric initiators as subassemblies, but include only the subassemblies themselves. In addition, electric initiators must be safe for handling, transportation, storage and use and must not deteriorate to a degree, which would render their performance or safety doubtful under normal service handling, adverse storage and transportation. RF susceptibility
Ident. Num:
MIL-DTL-2427  
  Rev. Num:

MIL-DTL-2427H, DETAIL SPECIFICATION BOX, AMMUNITION PACKING: WOOD, NAILED (5 SEP 2007) [SUPERSEDING MIL-B-2427G (AR)]., This specification covers three types and nine classes of basic box designs having two exterior vertical cleats on each end as shown in figure 1. Also, it covers the closing and strapping requirements for filled boxes (see Appendix A), and prescribe the criteria to be utilized to determine the serviceability of Government furnished boxes (see Appendix B). The box may or may not have hinge and hasp hardware, rope handles and double end construction.
Ident. Num:
MIL-DTL-24308 
  Rev. Num:

MIL-DTL-24308/6N, DETAIL SPECIFICATION, CONNECTORS, ELECTRIC, RECTANGULAR, MINIATURE, POLARIZED SHELL, RACK AND PANEL, RECEPTACLE SOCKET CONTACTS, NONMAGNETIC, CLASSES M AND N, CRIMP TYPE (25 JUN 2007)., The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24308.
Ident. Num:
MIL-DTL-24308 
  Rev. Num:

MIL-DTL-24308F, DETAIL SPECIFICATION CONNECTORS, ELECTRIC, RECTANGULAR, NONENVIRONMENTAL, MINIATURE, POLARIZED SHELL, RACK AND PANEL, GENERAL SPECIFICATION FOR (25 JUN 2007)., This specification covers the requirements for nonenvironmental, polarized shell, miniature, rack and panel connectors having pin and socket, crimp (removable), solder (nonremovable), or insulation displacement (nonremovable) contacts with rigid or float mounting, designed for -55C to +125C operating temperature range.
Ident. Num:
MIL-DTL-24441-27A 
  Rev. Num:

MIL-DTL-24441-27A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, NO. 50 GRAY, FORMULA 157, TYPE III (19 MAY 1999) [SUPERSEDING MIL-P-24441/27(SH)]., This formula covers no. 50 gray epoxy-polyamide paint designated Navy Formula 157, Type III for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441-39A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, YELLOW, FORMULA 161, TYPE IV (19 MAY 1999) [MIL-P-24441/39(SH)]., This formula covers yellow epoxy-polyamide paint designated Navy Formula 161, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/19B(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, ZINC PRIMER, FORMULA 159, TYPE III (19 MAY 1999)., This formula covers a cathodic protection zinc metal pigmented epoxy-polyamide paint designated Navy Formula 159, Type III for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/20A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, GREEN PRIMER, FORMULA 150, TYPE III (19 MAY 1999)., This formula covers green epoxy-polyamide paint designated Navy Formula 150, Type III for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/21A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, HAZE GRAY, FORMULA 151, TYPE III (19 MAY 1999)., This formula covers haze gray epoxy-polyamide paint designated Navy Formula 151, Type III for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/21A, DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, HAZE GRAY, FORMULA 151, TYPE III (19 MAY 1999) [SUPERSEDING MIL-P-24441/21(SH)]., The requirements for acquiring the product described herein shall consist of this specification and MIL-DTL-24441.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/22A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, WHITE, FORMULA 152, TYPE III (19 MAY 1999)., This formula covers white epoxy-polyamide paint designated Navy Formula 152, Type III for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/23A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, DARK GRAY RO1.8, FORMULA 153, TYPE III (19 MAY 1999)., This formula covers black epoxy-polyamide paint designated Navy Formula 153, Type III for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/24A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, DARK GRAY RO3.6, FORMULA 154, TYPE III (19 MAY1999)., This formula covers dark gray Ro3.6 epoxy-polyamide paint designated Navy Formula 154, Type III for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/25A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, DARK GRAY RO6, FORMULA 155, TYPE III (19 MAY 1999)., This formula covers dark gray Ro6 epoxy-polyamide paint designated Navy Formula 155, Type III for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/26A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, RED, FORMULA 156, TYPE III (19 MAY1999)., This formula covers red epoxy-polyamide paint designated Navy Formula 156, Type III for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/29A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, GREEN PRIMER, FORMULA 150, TYPE IV (19 MAY 1999)., This formula covers green epoxy-polyamide paint designated Navy Formula 150, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/30A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, HAZE GRAY, FORMULA 151, TYPE IV (19 MAY 1999)., This formula covers haze gray epoxy-polyamide paint designated Navy Formula 151, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/30A, DETAIL SPECIFICATION SHEET PAINT, EPOXY-POLYAMIDE, HAZE GRAY, FORMULA 151, TYPE IV (19 MAY 1999) [SUPERSEDING MIL-P-24441/30(SH)]., The requirements for acquiring the product described herein shall consist of this specification and MIL-DTL-24441.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/31A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, WHITE, FORMULA 152, TYPE IV (19 MAY 1999)., This formula covers white epoxy-polyamide paint designated Navy Formula 152, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/32A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, DARK GRAY RO1.8, FORMULA 153, TYPE IV (19 MAY 1999)., This formula covers black epoxy-polyamide paint designated Navy Formula 153, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/33A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, DARK GRAY RO3.6, FORMULA 154, TYPE IV (19 MAY 1999)., This formula covers black Ro3.6 epoxy-polyamide paint designated Navy Formula 154, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/34A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, DARK GRAY RO6, FORMULA 155, TYPE IV (19 MAY 1999)., This formula covers dark gray Ro6 epoxy-polyamide paint designated Navy Formula 155, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/35A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, RED, FORMULA 156, TYPE IV (19 MAY 1999)., This formula covers red epoxy-polyamide paint designated Navy Formula 156, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/36A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, NO. 50 GRAY, FORMULA 157, TYPE IV (19 MAY 1999)., This formula covers no. 50 gray epoxy-polyamide paint designated Navy Formula 157, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/37A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, YELLOW, FORMULA 158, TYPE IV (19 MAY 1999), This formula covers yellow epoxy-polyamide paint designated Navy Formula 158, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/38A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, BLACK, FORMULA 160, TYPE IV (19 MAY 1999)., This formula covers black epoxy-polyamide paint designated Navy Formula 160, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441/40A(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY-POLYAMIDE, RED, FORMULA 162, TYPE IV (19 MAY 1999)., This formula covers red epoxy-polyamide paint designated Navy Formula 162, Type IV for interior or exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441C (SH) (SUPPLEMENT 1), DETAIL SPECIFICATION, PAINT, EPOXY-POLYAMIDE, GENERAL SPECIFICATION FOR (19 MAY 1999)., This supplement forms a part of MIL-DTL-24441C(SH), dated 19 May 1999.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441C (SH), DETAIL SPECIFICATION, PAINT, EPOXY-POLYAMIDE, GENERAL SPECIFICATION FOR (19 MAY 1999) [SUPERSEDING MIL-P-24441B (SH)]., This specification covers a series of two component epoxy-polyamide paints designed to protect metal and plastic surfaces from environmental attack.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441C (SH), DETAIL SPECIFICATION, PAINT, EPOXY-POLYAMIDE, GENERAL SPECIFICATION FOR (19 MAY 1999) [SUPERSEDING MIL-P-24441B(SH)]., This specification covers a series of two component epoxypolyamide paints designed to protect metal and plastic surfaces from environmental attack.
Ident. Num:
MIL-DTL-24441 
  Rev. Num:

MIL-DTL-24441C(SH) (W/INTERIM AMENDMENT 1), DETAIL SPECIFICATION, PAINT, EPOXY-POLYAMIDE, GENERAL SPECIFICATION FOR (9 AUG 2006)., This specification covers a series of two component epoxy-polyamide paints designed to protect metal and plastic surfaces from environmental attack.
Ident. Num:
MIL-DTL-24487 
  Rev. Num:

MIL-DTL-24487B(SH), DETAIL SPECIFICATION, TILE, RUBBER VIBRATION DAMPING, TYPE V (28 JAN 2005) [SUPERSEDING MIL-T-24487A(SHIPS)]., This specification covers rubber tiles intended for damping vibrations in steel structures for shipboard use.
Ident. Num:
MIL-DTL-24631 
  Rev. Num:

MIL-DTL-24631/1C(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY, BLACK R0 1.8, NAVY FORMULA 184, TYPE I (METRIC) (6 JUN 1997)., This formula covers flexible epoxy paint MIL-DTL-24631/1C, type I, Navy Formula 184, Black, R0 1.8 paint for camouflage use. The paint shall consist of the ingredients specified in the quantities specified. Notes are indicated by / numbers.
Ident. Num:
MIL-DTL-24631 
  Rev. Num:

MIL-DTL-24631/2B(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY, DARK GRAY R0 3.6, NAVY FORMULA 185, TYPE I (METRIC) (6 JUN 1997)., This formula covers flexible epoxy paint MIL-DTL-24631/2B, type I, Navy Formula 185, Dark Gray, R 3.6 paint for camouflage use. The paint shall 0 consist of the ingredients specified in the quantities specified. Notes are indicated by / numbers.
Ident. Num:
MIL-DTL-24631 
  Rev. Num:

MIL-DTL-24631/3B(SH), DETAIL SPECIFICATION SHEET, PAINT, EPOXY, WHITE, NAVY FORMULA 186, TYPE I (METRIC) (6 JUN 1997)., This formula covers flexible epoxy paint MIL-DTL-24631/3B, type I, Navy Formula 186, White for exterior use. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24631 

MIL-DTL-24631/7(SH), DETAIL SPECIFICATION SHEET, PAINT, POLYESTER URETHANE, BLACK, NAVY FORMULA 187, TYPE II (METRIC) (6 JUN 1997)., This formula covers polyester urethane paint, MIL-DTL-24631/7, type II, Navy Formula 187, Black RW 1.8, Type II for exterior use as a highly flexible, weather resistant topcoat. The paint shall consist of the ingredients specified in the quantities specified.
Ident. Num:
MIL-DTL-24631A 
  Rev. Num:

MIL-DTL-24631A (SH) (w/ INTERIM AMENDMENT 1), DETAIL SPECIFICATION PAINT, CAMOUFLAGE FOR SUBMARINES, GENERAL SPECIFICATION FOR (9 AUG 2006) [USED IN LIEU OF MIL-DTL-24631A(SH)]., This specification covers requirements for two colors of camouflage paint and a flexible white marking paint.
Ident. Num:
MIL-DTL-24631 
  Rev. Num:

MIL-DTL-24631A (SH), DETAIL SPECIFICATION PAINT, CAMOUFLAGE FOR SUBMARINES, GENERAL SPECIFICATION FOR (6 JUN 1997) [SUPERSEDING DOD-P-24631(SH)]., This specification covers requirements for two colors of camouflage paint and a flexible white marking paint.
Ident. Num:
MIL-DTL-24631 
  Rev. Num:

MIL-DTL-24631A(SH), DETAIL SPECIFICATION, PAINT, CAMOUFLAGE FOR SUBMARINES, GENERAL SPECIFICATION FOR (METRIC) (6 JUN 1997)., This specification covers requirements for two colors of camouflage paint and a flexible white marking paint.
Ident. Num:
MIL-DTL-24640 
  Rev. Num:

MIL-DTL-24640B (w/ AMENDMENT 1)., DETAIL SPECIFICATION CABLES, LIGHT-WEIGHT, ELECTRIC, FOR SHIPBOARD USE, GENERAL SPECIFICATION FOR (16 DEC 2004) [SUPERSEDING MIL-C-24640A]., This specification covers light-weight electric cables for Navy shipboard applications.
Ident. Num:
MIL-DTL-24696 
  Rev. Num:

MIL-DTL-24696C, DETAIL SPECIFICATION, GASKET, SHEET, NON-ASBESTOS (5 SEP 2008) [SUPERSEDING MIL-B-24696B]., This specification establishes the requirements of non-asbestos sheet gasket material for nonpropulsion and propulsion steam and water applications and for all petroleum based hydraulic and lube oil applications.
Ident. Num:
MIL-DTL-24779 
  Rev. Num:

MIL-DTL-24779A(SH), DETAIL SPECIFICATION, ANODES, SACRIFICIAL ALUMINUM ALLOY (6 OCT 2006) [SUPERSEDING MIL-A-24779 (SH)]., This specification covers the general requirements and inspections for aluminum alloy sacrificial anodes for U.S. Navy ships and submarines.
Ident. Num:
MIL-DTL-24784 
  Rev. Num:

MIL-DTL-24784/22, DETAIL SPECIFICATION SHEET TECHNICAL CONTENT DEVELOPMENT REQUIREMENTS FOR COMBAT SYSTEM TECHNICAL OPERATIONS MANUALS (CSTOMS); HULL, MECHANICAL, AND ELECTRICAL (HM&E) SYSTEM AND EQUIPMENT MANUALS; ELECTRONIC [INCLUDING SERVICE TEST ELECTRONIC, EXPERIMENTAL ELECTRONIC AND INTERIOR COMMUNICATION (IC)] SYSTEM AND EQUIPMENT MANUALS; AND WEAPON SYSTEMS AND WEAPON EQUIPMENT MANUALS (3 NOV 2007)., This specification sets forth content requirements for the preparation of technical manuals (TMs) covering description, operation, maintenance, installation, and parts support for Combat System Technical Operations Manuals (CSTOMs); Hull, Mechanical, and Electrical (HM&E) Systems and Equipment Manuals; Electronic [including Service Test Electronic, Experimental Electronic, and Interior Communications (IC)] System and Equipment Manuals; and Weapon Systems and Weapon Equipment Manuals. The requirements are applicable for the output of paper or for the display of page-oriented, linear, and non-linear TMs on an Electronic Display System (EDS).
Ident. Num:
MIL-DTL-24784 
  Rev. Num:

MIL-DTL-24784C (NAVY) (SUPPLEMENT 1), DETAIL SPECIFICATION MANUALS, TECHNICAL: GENERAL ACQUISITION AND DEVELOPMENT REQUIREMENTS, GENERAL SPECIFICATION FOR (3 NOV 2007). This supplement forms a part of MIL-DTL-24784C(NAVY) dated 3 November 2007.
Ident. Num:
MIL-DTL-24784 
  Rev. Num:

MIL-DTL-24784C (NAVY), DETAIL SPECIFICATION MANUALS, TECHNICAL: GENERAL ACQUISITION AND DEVELOPMENT REQUIREMENTS, GENERAL SPECIFICATION FOR (3 NOV 2007)., This specification establishes the general acquisition and development requirements needed to prepare digital technical information for multi-output presentation of NAVSEA Technical Manuals (TMs) (see 6.4.21). The technical content and style and format requirements contained in this specification can be used to develop and assemble complete TMs for ships, shipboard systems (see 6.4.20), and equipment. The requirements apply to the output of paper TMs or, to the display of page-oriented linear and non-linear Interactive Electronic Technical Manuals (IETMs) (see 6.4.10) on an Electronic Display System (EDS).
Ident. Num:
MIL-DTL-25027 
  Rev. Num:

MIL-DTL-25027H (AMENDMENT 1), DETAIL SPECIFICATION, NUT, SELF-LOCKING, 250 DEG. F, 450 DEG. F, AND 800 DEG. F (2 DEC 1998) [SUPERSEDING MIL-N-25027G] [S/S BY NASM-25027]., This amendment forms a part of Military Specification MIL-DTL-25027H, dated 15 August 1997, and is approved for use by all Departments and Agencies of the Department of Defense.
Ident. Num:
MIL-DTL-25027 
  Rev. Num:

MIL-DTL-25027H, DETAIL SPECIFICATION, NUT, SELF-LOCKING, 250 DEG. F, 450 DEG. F, AND 800 DEG. F (15 AUG 1997) [SUPERSEDING MIL-N-25027G] [S/S BY NASM-25027]., This specification covers self-locking nuts for use in temperatures of 250 F, 450 F, and 800F (see 6.1).
Ident. Num:
MIL-DTL-25524 
  Rev. Num:

MIL-DTL-25524E(USAF), DETAIL SPECIFICATION, TURBINE FUEL, AVIATION, THERMALLY STABLE (20 NOV 1997) [SUPERSEDING MIL-T-25524D(USAF)]., This specification was thoroughly reviewed as a part of acquisition reform. While most of the requirements were converted to performance terms, due to the military-unique nature of the product (see 6.1) and the need for compatibility with deployed systems, it was determined that not all requirements could be converted. The issuance of this specification as ?detail? is not intended to constrain technology advances in future systems. This specification covers one grade of turbine fuel designated as JPTS (see 6.1).
Ident. Num:
MIL-DTL-25579 
  Rev. Num:

MIL-DTL-25579F, MILITARY SPECIFICATION HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, HIGH TEMPERATURE, MEDIUM PRESSURE, GENERAL SPECIFICATION FOR (10 JUL 2006)., This specification contains the requirements for medium pressure, high temperature, polytetrafluoroethylene (PTFE) hose assemblies, reinforced with a corrosion-resistant steel (CRES) wire braid for use in fuel, lubricating oil, water-alcohol, hydraulics and pneumatic systems within the limits specified herein.
Ident. Num:
MIL-DTL-25708 
  Rev. Num:

MIL-DTL-25708D (AMENDMENT 1), DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (1 OCT 2001) [SUPERSEDING MIL-A-25708C]., This amendment forms a part of MIL-DTL-25708D, dated 23 July 1999, and is approved for use by all Departments and Agencies of the Department of Defense.
Ident. Num:
MIL-DTL-25708 
  Rev. Num:

MIL-DTL-25708D, DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (23 JUL 1999) [SUPERSEDING MIL-A-25708C]., This document covers the general requirements (for externally mounted) blade type L-band antennas (see 6.1).
Ident. Num:
MIL-DTL-25708 
  Rev. Num:

MIL-DTL-25708E, DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (2 OCT 2006) [SUPERSEDING MIL-DTL-25708D AND MIL-A-25708C]., This document covers the general requirements (for externally mounted) blade type L-band antennas (see 6.1).
Ident. Num:
MIL-DTL-25708 
  Rev. Num:

MIL-DTL-25708F, DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (28 MAY 2008)., This document covers the general requirements (for externally mounted) blade type L-band antennas (see 6.1).
Ident. Num:
MIL-DTL-25988 
  Rev. Num:

MIL-DTL-25988C, DETAIL SPECIFICATION, RUBBER, FLUOROSILICONE ELASTOMER, OIL-AND-FUEL RESISTANT, SHEETS, STRIPS, MOLDED PARTS, AND EXTRUDED SHAPES (14 AUG 2006) [SUPERSEDING MIL-R-25988B]., This specification covers oil- and -fuel-resistant fluorosilicone elastomer rubber sheets, strips, molded parts, and extruded shapes for aeronautical and aerospace applications..
Ident. Num:
MIL-DTL-26074 
  Rev. Num:

MIL-DTL-26074F (NOTICE 1), DETAIL SPECIFICATION COATINGS, ELECTROLESS NICKEL, REQUIREMENTS FOR. MIL-DTL-26074F is hereby cancelled. Previous users for Naval Nuclear Propulsion Program applications only should refer to MIL-DTL-32119. Previous users of MIL-C- 26074E should refer to SAE AMS-C-26074. If copies of MIL-DTL-26074F are needed for historical purposes, contact NAVSEA 05Q, 1333 Isaac Hull Avenue SE, STOP 5160, Washington Navy Yard, DC 20376-5160.
Ident. Num:
MIL-DTL-26074 
  Rev. Num:

MIL-DTL-26074F, DETAIL SPECIFICATION COATINGS, ELECTROLESS NICKEL, REQUIREMENTS FOR. MIL-DTL-26074F is a controlled distribution document. If copies of MIL-DTL-26074F are needed for historical purposes, contact NAVSEA 05Q, 1333 Isaac Hull Avenue SE, Stop 5160, Washington Navy Yard, DC 20376-5160.
Ident. Num:
MIL-DTL-26482 
  Rev. Num:

MIL-DTL-26482H (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, (CIRCULAR, MINIATURE, QUICK DISCONNECT, ENVIRONMENT RESISTING), RECEPTACLES AND PLUGS, GENERAL SPECIFICATION FOR (20 FEB 2007) [SUPERSEDING MIL-C-26482G]., This supplement forms a part of MIL-DTL-26482H, dated 20 February 2007.
Ident. Num:
MIL-DTL-26482 
  Rev. Num:

MIL-DTL-26482H, DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, (CIRCULAR, MINIATURE, QUICK DISCONNECT, ENVIRONMENT RESISTING), RECEPTACLES AND PLUGS, GENERAL SPECIFICATION FOR (20 FEB 2007) [SUPERSEDING MIL-C-26482G]., This specification covers the general requirements for two series of environment resisting, quick disconnect, miniature, circular electrical connectors (and accessories). Each series contains hermetic receptacles. The two series of connectors are intermateable when using power contacts and are not intermateable when using shielded contacts. When intermated, the minimum performance requirement for series 1 connectors will be met.
Ident. Num:
MIL-DTL-26500 
  Rev. Num:

MIL-DTL-26500F (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS, GENERAL PURPOSE, ELECTRICAL, MINIATURE, CIRCULAR, ENVIRONMENT RESISTING, GENERAL SPECIFICATION FOR (6 FEB 2004)., This supplement forms a part of MIL-DTL-26500F, dated 6 February 2004.
Ident. Num:
MIL-DTL-26500 
  Rev. Num:

MIL-DTL-26500F, DETAIL SPECIFICATION CONNECTORS, GENERAL PURPOSE, ELECTRICAL, MINIATURE, CIRCULAR, ENVIRONMENT RESISTING, GENERAL SPECIFICATION FOR (6 FEB 2004)., This specification covers an environment-resisting family of miniature, circular, electrical connectors (plugs and receptacles), designed to meet the requirements of aerospace vehicles.
Ident. Num:
MIL-DTL-26894 
  Rev. Num:

MIL-DTL-26894D, DETAIL SPECIFICATION, HOSE AND HOSE ASSEMBLY, RUBBER, GASOLINE, REFUELING, LOW TEMPERATURE (30 JUN 1998)., This specification contains the requirements for a low temperature, 4-inch ID gasoline refueling rubber hose and hose assembly.
Ident. Num:
MIL-DTL-2726 
  Rev. Num:

MIL-DTL-2726/37F, DETAIL SPECIFICATION SHEET, RECEPTACLE, ELECTRICAL, 15 - AMPERE, 125 - VOLT, 60 HERTZ, BLADED TYPE, GROUNDED (SYMBOL NO. 1099.1) (01 NOV 2006) [SUPERSEDING MIL-R-2726/37E]., The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-2726.
Ident. Num:
MIL-DTL-2726/73C 
  Rev. Num:

MIL-DTL-2726/73C, DETAIL SPECIFICATION SHEET, RECEPTACLE, ELECTRICAL, 15-AMPERE, 125-VOLT, BLADED TYPE, GROUNDED (PORTABLE) (SYMBOL NO. 1215) (31 AUG 2005) [SUPERSEDING MIL-R-2726/73B(SH)]., The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-2726.
Ident. Num:
MIL-DTL-2726 
  Rev. Num:

MIL-DTL-2726C (SUPPLEMENT 1), DETAIL SPECIFICATION, RECEPTACLE, RECEPTACLE PLUGS, SWITCH AND RECEPTACLES, AND OUTLETS (ELECTRICAL), GENERAL SPECIFICATION FOR (14 FEB 2006) [SUPERSEDING MIL-R-2726B (SH)]., This supplement forms a part of MIL-DTL-2726C, dated 14 February 2006.
Ident. Num:
MIL-DTL-2726 
  Rev. Num:

MIL-DTL-2726C, DETAIL SPECIFICATION, RECEPTACLE, RECEPTACLE PLUGS, SWITCH AND RECEPTACLES, AND OUTLETS (ELECTRICAL), GENERAL SPECIFICATION FOR (14 FEB 2006) [SUPERSEDING MIL-R-2726B (SH)]., This specification covers the general requirements for power type electrical plugs, receptacles, switch and receptacle combinations, and outlets for use in direct current (dc) circuits up to 250 volts, or in alternating current (ac) circuits up to 600 volts at frequencies up to and including 400 Hz.
Ident. Num:
MIL-DTL-27272 
  Rev. Num:

MIL-DTL-27272C (SUPPLEMENT 1), DETAIL SPECIFICATION, FITTINGS, POLYTETRAFLUOROETHYLENE HOSE, HIGH-TEMPERATURE, MEDIUM-PRESSURE, GENERAL SPECIFICATION FOR (25 SEP 2003) [SUPERSEDING MIL-F-27272B]., This supplement forms a part of MIL-DTL-27272C, dated 28 Aug 2003
Ident. Num:
MIL-DTL-27272 
  Rev. Num:

MIL-DTL-27272C, DETAIL SPECIFICATION, FITTINGS, POLYTETRAFLUOROETHYLENE HOSE, HIGH-TEMPERATURE, MEDIUM-PRESSURE, GENERAL SPECIFICATION FOR (25 SEP 2003) [SUPERSEDING MIL-F-27272B]., This specification covers the requirements for fittings for medium-pressure and high- temperature applications with polytetrafluoroethylene (PTFE) hose conforming to MIL-DTL-27267 and MIL-DTL-25579 (see 3.1 and 6.1).
Ident. Num:
MIL-DTL-27443 
  Rev. Num:

MIL-DTL-27443F (USAF), DETAILED SPECIFICATION PALLETS, CARGO, AIRCRAFT, TYPE HCU-6/E AND HCU-12/E (15 JUL 2003)., Pallets, cargo, aircraft, covered by this specification have a capacity of 10,000 pounds and 5,000 pounds.
Ident. Num:
MIL-DTL-27500 
  Rev. Num:

MIL-DTL-27500H (AMENDMENT 1), MILITARY SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (S/S BY NEMA-WC27500) (26 NOV 1999) (SUPERSEDING MIL-C-27500G)., This amendment forms a part of MIL-DTL-27500H, dated 10 December 1997, and is approved for use by all Departments and Agencies of the Department of Defense.
Ident. Num:
MIL-DTL-27500 
  Rev. Num:

MIL-DTL-27500H (NOTICE 1), MILITARY SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (S/S BY NEMA-WC27500) (16 APR 2001) (SUPERSEDING MIL-C-27500G)., MIL-DTL-27500H, dated 10 December 1997, is hereby canceled. Future acquisitions for this material should refer to National Electrical Manufacturers Association (NEMA) WC 27500, Standard for Aerospace and Industrial Electric Cable.
Ident. Num:
MIL-DTL-27500 
  Rev. Num:

MIL-DTL-27500H, MILITARY SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (S/S BY NEMA-WC27500) (10 December 1997) (SUPERSEDING MIL-C-27500G)., This specification covers the requirements for special purpose and power electrical cable. (see 6.1)
Ident. Num:
MIL-DTL-27500 
  Rev. Num:

MIL-DTL-27500H, DETAIL SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (10 DEC 1997)., This specification covers the requirements for special purpose and power electrical cable. (see 6.1)
Ident. Num:
MIL-DTL-27536 
  Rev. Num:

MIL-DTL-27536C, DETAIL SPECIFICATION, COUPLING, CLAMP, GROOVED, V-BAND (15 DEC 1995) [SUPERSEDING MIL-C-27536B ] [S/S BY SAE-AS5355]., This specification establishes the general requirements for V-band grooved clamp couplings.
Ident. Num:
MIL-DTL-27686 
  Rev. Num:

MIL-DTL-27686G (NOTICE 2), DETAIL SPECIFICATION, INHIBITOR, ICING, FUEL SYSTEM (15 MAR 2006) [S/S BY MIL-DTL-85470] [SUPERSEDING MIL-I-27686F].
Ident. Num:
MIL-DTL-27686 
  Rev. Num:

MIL-DTL-27686G, DETAIL SPECIFICATION, INHIBITOR, ICING, FUEL SYSTEM (22 DEC 1997) [S/S BY MIL-DTL-85470] [SUPERSEDING MIL-I-27686F]., This specification covers the requirements for one type of fuel system icing inhibitor soluble in jet turbine fuels. Fuel System Icing Inhibitor is identified by NATO Code Number S-748 (see 1.2 and 6.7). This specification was thoroughly reviewed as a part of acquisition reform. While most of the requirements were converted to performance terms, due to the military-unique nature of the product (see 6.1) and the need for compatibility with deployed systems, it was determined that not all requirements could be converted. The issuance of this specification as "detail" is not intended to constrain technology advances in future systems.
Ident. Num:
MIL-DTL-2845 
  Rev. Num:

MIL-DTL-2845E (sh), DETAIL SPECIFICATION PROPULSION SYSTEMS, BOAT AND SHIP; MAIN SHAFTING, PROPELLERS, BEARINGS, GAUGES, SPECIAL TOOLS, AND ASSOCIATED REPAIR PARTS; PRESERVATION, PACKAGING, PACKING AND STORAGE OF. This specification covers the cleaning, drying, preservation, packing, marking, and storage of main propulsion shafting, line shaft bearings, stern tube and strut bearings, boat and ship propellers, propeller devices including controllable pitch propellers, shafting, and accessories thereto. It also covers repair parts, tools, and independently mounted main propulsion thrust bearings.
Ident. Num:
MIL-DTL-28619 
  Rev. Num:

MIL-DTL-28619D, DETAIL SPECIFICATION ANCHORS, STATO MOORING, 200 TO 15,000 POUNDS (20 OCT 97). This specification covers stato mooring anchors, including stabilizers, wedges, and palm extensions.
Ident. Num:
MIL-DTL-28689 
  Rev. Num:

MIL-DTL-28689C, MILITARY SPECIFICATION, CONTAINERS, SHIPPING AND STORAGE, STEEL WALL (WITH AND WITHOUT CABINETRY) (17 JAN 1997) [SUPERSEDING MIL-C-28689B (YD)]., This specification covers equipment containers used to store and ship items listed in Naval Construction Force tables of allowance. The containers are of two sizes and either empty for bulk loading of materials or configured with cabinetry to simplify locating parts and equipment for distribution.
Ident. Num:
MIL-DTL-28786 
  Rev. Num:

MIL-DTL-28786C, DETAIL SPECIFICATION, SWITCHES, ELECTRICAL AND FIBER OPTIC, PACKAGING OF (31 JAN 2004) [SUPERSEDING MIL-S-28786B]., This specification covers the requirements for the preservation, packing, and container marking for all types of electrical and fiber optic switches, switch assemblies, and associated accessories that are primarily in FSCs 5930 and 6021. As used in this specification, the term switches will also include switch assemblies.
Ident. Num:
MIL-DTL-287 
  Rev. Num:

MIL-DTL-287H, DETAIL SPECIFICATION, WAVEGUIDE ASSEMBLIES, FLEXIBLE, TWISTABLE AND NON-TWISTABLE, GENERAL SPECIFICATION FOR (28 SEP 2007)[SUPERSEDING MIL-W-287E]., This specification covers the general requirements for twistable and non-twistable, flexible waveguide assemblies (hereinafter referred to as assemblies) (see 6.1).
Ident. Num:
MIL-DTL-28999 
  Rev. Num:

MIL-DTL-28999C (MC), DETAIL SPECIFICATION, PUBLICATIONS, TECHNICAL, INSTRUCTION-TYPE: PREPARATION OF (6 FEB 2001) [SUPERSEDING MIL-P-28999B(MC)]., This specification covers general style and format requirements for the preparation of instruction-type technical publications for support of in-service equipment/weapons systems.
Ident. Num:
MIL-DTL-29183 
  Rev. Num:

MIL-DTL-29183/7B, DETAIL SPECIFICATION SHEET PANELBOARD, POWER DISTRIBUTION, PORTABLE, WEATHERPROOF, TYPE I, CLASS 1, CONFIGURATION 5: 480 OR 208 VOLT, 120 KILOWATT, TERMINAL TYPE CONNECTORS (13 MAR 03)., This specification is approved for use by all departments and agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the issue of MIL-DTL-29183 listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation.
Ident. Num:
MIL-DTL-29229 
  Rev. Num:

MIL-DTL-29229B (YD), DETAIL SPECIFICATION SWITCHES AND FROGS, TRACK, FABRICATED, FOR PORTAL CRANES (14 MAR 1997) [SUPERSEDING MIL-S-29229A(YD)] ., This document covers special fabricated track switches and frogs for portal crane tracks.
Ident. Num:
MIL-DTL-29395 
  Rev. Num:

MIL-DTL-29395B, DETAIL SPECIFICATION SLACKS, WOMEN'S - MUSICIAN'S (21 OCT 1997) [SUPERSEDING MIL-S-29395A]., This specification covers the requirements for slacks for wear by female members of the U.S. Marine Band.
Ident. Num:
MIL-DTL-29479 
  Rev. Num:

MIL-DTL-29479A (MC), DETAIL SPECIFICATION SLACKS, WOMEN'S (21 OCT 1997) [SUPERSEDING MIL-S-29479 (MC)]., This specification covers the requirements for women's slacks.
Ident. Num:
MIL-DTL-2 
  Rev. Num:

MIL-DTL-2G (SUPPLEMENT 1), DETAIL SPECIFICATION, VALVES, CYLINDER, GAS (FOR COMPRESSED OR LIQUEFIED GASES), GENERAL SPECIFICATION FOR (29 SEP 2006) [SUPERSEDING MIL-V-2D]., This supplement forms a part of MIL-DTL-2G, dated 29 September 2006.
Ident. Num:
MIL-DTL-2 
  Rev. Num:

MIL-DTL-2G, DETAIL SPECIFICATION, VALVES, CYLINDER, GAS (FOR COMPRESSED OR LIQUEFIED GASES), GENERAL SPECIFICATION FOR (29 SEP 2006) [SUPERSEDING MIL-V-2D]., This specification provides design and operational requirements for cylinder valves (see 6.7.3) used with compressed gas (see 6.7.1) cylinders containing liquefied (see 6.7.7) or non-liquefied compressed gases (see 6.7.8) or mixtures.
Ident. Num:
MIL-DTL-31000 
  Rev. Num:

MIL-DTL-31000A (AMENDMENT 1), DETAIL SPECIFICATION, TECHNICAL DATA PACKAGES (15 OCT 1998)., This amendment forms a part of MIL-DTL-31000A, dated 9 June 1997, and is approved for use by all Departments and Agencies of the Department of Defense.
Ident. Num:
MIL-DTL-31000 
  Rev. Num:

MIL-DTL-31000A, DETAIL SPECIFICATION, TECHNICAL DATA PACKAGES (9 JUL 1997). This specification prescribes the requirements for preparing a technical data package (TDP) which is composed of one or more TDP elements and related TDP data management products (See 6.1). This specification does not apply to financial, management, or contract administrative data.
Ident. Num:
MIL-DTL-31000 
  Rev. Num:

MIL-DTL-31000B, DETAIL SPECIFICATION, TECHNICAL DATA PACKAGES (14 DEC 2001)., This specification prescribes the requirements for preparing a technical data package (TDP), which is composed of one or more TDP elements and related TDP data management products (See 6.1). This specification does not apply to financial, management, or contract administrative data.
Ident. Num:
MIL-DTL-31000 
  Rev. Num:

MIL-DTL-31000C, DETAIL SPECIFICATION, TECHNICAL DATA PACKAGES (9 JUL 2004)., This specification prescribes the requirements for preparing a technical data package (TDP), which is composed of one or more TDP elements and related TDP data management products (See 6.1). This specification does not apply to financial, management, or contract administrative data.
Ident. Num:
MIL-DTL-31011 
  Rev. Num:

MIL-DTL-31011A, DETAILED SPECIFICATION CLOTH, WATERPROOF AND MOISTURE VAPOR PERMEABLE (6 DEC 2000) [SUPERSEDING MIL-PRF-31011 AND MIL-C-44187]., This document covers the requirements for four types of woodland camouflage cloth, which are waterproof, and moisture vapor permeable.
Ident. Num:
MIL-DTL-31011 
  Rev. Num:

MIL-DTL-31011B, DETAILED SPECIFICATION CLOTH, WATERPROOF AND MOISTURE VAPOR PERMEABLE (10 FEB 2005)., This document covers the requirements for four types of camouflage cloth, which are waterproof and moisture vapor permeable.
Ident. Num:
MIL-DTL-31011 
  Rev. Num:

MIL-DTL-31011B, DETAILED SPECIFICATION CLOTH, WATERPROOF AND MOISTURE VAPOR PERMEABLE (10 FEB 2005)., This document covers the requirements for four types of camouflage cloth, which are waterproof and moisture vapor permeable.
Ident. Num:
MIL-DTL-32169 
  Rev. Num:

MIL-DTL-32169, DETAIL SPECIFICATION, WHEEL ASSEMBLIES, POLYURETHANE; FOR THE BRADLEY FIGHTING VEHICLE (30 NOV 2004)., This specification covers roadwheels for use on the Bradley Fighting Vehicle. These are metal wheels with bonded polyurethane tires (see 6.1). For the purpose of this specification polyurethane may be any form of thermoplastic or thermosetting resins. The contractor is held fully responsible for the entire assembly/component including non-elastomeric components and fasteners.
Ident. Num:
MIL-DTL-32201 
  Rev. Num:

MIL-DTL-32201, DETAIL SPECIFICATION, MIRROR ASSEMBLIES, REARVIEW, HMMWV STYLE, 12x8 INCH (NOMINAL), EXTERIOR MOUNTING (13 MAR 2006)., This document covers exterior-mounted, automotive rearview mirror assemblies, without hardware or bracketry required to mount the mirror assembly to the US Army HMMWV, Armored Security Vehicle (ASV), and other type vehicles.
Ident. Num:
MIL-DTL-32258 
  Rev. Num:

MIL-DTL-32258, DETAIL SPECIFICATION NUT, SELF-LOCKING (RING TYPE NON-METALLIC INSERT), HEAVY HEX, CONTROLLED ROOT RADIUS, NICKEL-COPPER ALLOY (28 JUN 2007) (SUPERSEDING MIL-N-25027/1A)., This specification covers ring-type, self-locking, heavy hex, nickel-copper alloy nuts, with screw threads with a controlled root radius for use in general shipboard applications. Coarse pitch series and eight pitch series of threads are covered by this specification. Nuts with a nominal diameter between and 2 inches are covered in this specification.
Ident. Num:
MIL-DTL-32262 
  Rev. Num:

MIL-DTL-32262, DETAIL SPECIFICATION, ARMOR PLATE, ALUMINUM ALLOY, UNWELDABLE APPLIQUE 6061 (31 JUL 2007)., This specification covers unweldable 6061 wrought aluminum alloy armor plate in nominal thicknesses from 0.250 to 3.000 inch, inclusive (see 6.2). The weldability of 6061 wrought aluminum alloy armor has not been determined. Therefore, these alloys should be used as an appliqu armor.
Ident. Num:
MIL-DTL-32266  
  Rev. Num:

MIL-DTL-32266, DETAIL SPECIFICATION, WIRE ROPE, 1.5 INCH DIAMETER, GALVANIZED, COMPACTED STRAND, FOR AIRCRAFT ELEVATOR (8 JUN 2008)., This specification covers the requirements for 1.5 inch diameter, galvanized, compacted strand construction wire rope (see 6.4.8 and 6.4.9) used for Navy shipboard aircraft elevators. The wire rope must provide high tensile stiffness to minimize the changes in platform elevation associated with roll-on and roll-off of aircraft and a uniform density that provides consistent tension values in service. It must also provide good bending fatigue performance to accommodate repeated cycling over the various sheaves in the elevator system. The rope must be resistant to corrosion associated with continual exposure to and operation in a salt water environment.
Ident. Num:
MIL-DTL-3432 
  Rev. Num:

MIL-DTL-3432H, DETAIL SPECIFICATION CABLES, (POWER AND SPECIAL PURPOSE) AND WIRE, ELECTRICAL (300 AND 600 VOLTS) (23 JAN 2006)., This specification covers single and multiple conductor cables with and without shields for use in 300 and 600 volts root mean square (rms) applications (see 6.1).
Ident. Num:
MIL-DTL-3661 
  Rev. Num:

MIL-DTL-3661C, DETAIL SPECIFICATION, LAMPHOLDERS, INDICATOR LIGHTS, INDICATOR LIGHT HOUSINGS, AND INDICATOR LIGHT LENSES, GENERAL SPECIFICATION FOR (10 JUN 2003) [SUPERSEDING MIL-L-3661B SUPPLEMENT 1B]., This supplement forms a part of MIL-DTL-3661C, dated 10 JUNE 2003.
Ident. Num:
MIL-DTL-3661 
  Rev. Num:

MIL-DTL-3661C, DETAIL SPECIFICATION, LAMPHOLDERS, INDICATOR LIGHTS, INDICATOR LIGHT HOUSINGS, AND INDICATOR LIGHT LENSES, GENERAL SPECIFICATION FOR (10 JUN 2003) [SUPERSEDING MIL-L-3661B]., This specification covers the general requirements for lampholders, indicator lights, indicatorlight housings, and indicator-light lenses including display and integral lamp driver network types and associated hardware. For the purpose of this specification, an indicator-light housing is an indicator light without a lens (see 6.5).
Ident. Num:
MIL-DTL-3701 
  Rev. Num:

MIL-DTL-3701D, DETAILED SPECIFICATION CYLINDERS, COMPRESSED GAS: DOT-8 ACETYLENE, WITH VALVES (14 SEP 2007)., This specification covers new steel cylinders, with applicable valves and caps, intended for acetylene service.
Ident. Num:
MIL-DTL-3702 
  Rev. Num:

MIL-DTL-3702D, DETAIL SPECIFICATION, CABLE, POWER, ELECTRICAL: IGNITION, HIGH-TENSION (8 JAN 2008) [SUPERSEDING MIL-C-3702B]., This specification covers shielded and unshielded electrical power cable for use on high-tension ignition systems (see 6.1).
Ident. Num:
MIL-DTL-38195 
  Rev. Num:

MIL-DTL-38195D, DETAIL SPECIFICATION, GENERATOR SET, GAS TURBINE ENGINE, 60 kW, 400 Hz, GENERAL PURPOSE (1 APR 2000) [SUPERSEDING MIL-G-38195C]., This specification covers general requirements for a general purpose, tactical generator set (herein after termed set), rated to 60 Kilowatts (kW) direct current (DC) and 60 kW at 400-Hertz (Hz) alternating current (AC). The set will include a wheel-mounted, towable, gas turbine engine-driven, Model MEP-356A (Air Force Model A/M32A-60A).
Ident. Num:
MIL-DTL-38999/20 
  Rev. Num:

METRIC MIL-DTL-38999/20F 17 May 2007 SUPERSEDING MIL-DTL-38999/20E 11 June 2001 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, CIRCULAR, RECEPTACLE, THREADED, WALL MOUNTING FLANGE, REMOVABLE CRIMP CONTACTS, SERIES III, METRIC This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-38999.
Ident. Num:
MIL-DTL-38999/26 
  Rev. Num:

METRIC MIL-DTL-38999/26E 11 June 2001 SUPERSEDING MIL-C-38999/26D 7 May 1990 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, PLUG, CIRCULAR, THREADED, STRAIGHT, REMOVABLE CRIMP CONTACTS, SERIES III, METRIC This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-DTL-38999.
Ident. Num:
MIL-DTL-38999 
  Rev. Num:

MIL-DTL-38999K (AMENDMENT 1), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (25 MAY 2001)., This amendment forms a part of MIL-DTL-38999K, dated 17 December 1999, and is approved for use by all Departments and Agencies of the Department of Defense.
Ident. Num:
MIL-DTL-38999 
  Rev. Num:

MIL-DTL-38999K (AMENDMENT 2), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (19 APR 2002).,
Ident. Num:
MIL-DTL-38999 
  Rev. Num:

MIL-DTL-38999K (AMENDMENT 3), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (22 AUG 2003)., This amendment forms a part of MIL-DTL-38999K, dated 17 December 1999, and is approved for use by all Departments and Agencies of the Department of Defense.
Ident. Num:
MIL-DTL-38999 
  Rev. Num:

MIL-DTL-38999K (SUPPLEMENT 1), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (12 JUL 2002)., This supplement forms a part of MIL-DTL-38999K, dated 17 December 1999.
Ident. Num:
MIL-DTL-38999  
  Rev. Num:

MIL-DTL-38999K, CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (17 DEC 1999)., This specification covers four series of miniature, high density, bayonet, threaded, or breech coupling, circular, environment resistant, electrical connectors using removable crimp or fixed hermetic solder contacts, and are capable of operation within a temperature range of -65 deg. C to +200 deg. C.
Ident. Num:
MIL-DTL-38999 
  Rev. Num:

MIL-DTL-38999L (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (30 MAY 2008) [SUPERSEDING MIL-C-38999]., This supplement forms a part of MIL-DTL-38999L, dated 30 May 2008.
Ident. Num:
MIL-DTL-38999 
  Rev. Num:

MIL-DTL-38999L, DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (30 MAY 2008) [SUPERSEDING MIL-C-38999]., This specification covers four series of miniature, high density, bayonet, threaded, or breech coupling, circular, environment resistant, electrical connectors using removable crimp or fixed hermetic solder contacts, and are capable of operation within a temperature range of -65?C to +200?C (see 1.3.1d). See 6.1 for intended use and applications.
Ident. Num:
MIL-DTL-39024 
  Rev. Num:

MIL-DTL-39024B (SUPPLEMENT 1), DETAIL SPECIFICATION, JACK, TIP (TEST POINT, PANEL OR PRINTED WIRING TYPE), GENERAL SPECIFICATION FOR (3 FEB 2003) [SUPERSEDING MIL-C-39024A].
Ident. Num:
MIL-DTL-39024 
  Rev. Num:

MIL-DTL-39024B, DETAIL SPECIFICATION, JACK, TIP (TEST POINT, PANEL OR PRINTED WIRING TYPE), GENERAL SPECIFICATION FOR (3 FEB 2003) [SUPERSEDING MIL-C-39024A]., This specification covers the general requirements for panel or printed wiring type test point connectors for use in electrical and electronic equipment (see 6.1). As used in this specification, the term "connectors" includes tip jacks.
Ident. Num:
MIL-DTL-39028 
  Rev. Num:

MIL-DTL-39028E, DETAIL SPECIFICATION, CAPACITORS, PACKAGING OF (25 JUL 2007)., This specification covers the requirements for the preservation, packing, and container marking of all types of capacitors and associated accessories that are primarily in FSC 5910 (see 6.1).
Ident. Num:
MIL-DTL-39030 
  Rev. Num:

MIL-DTL-39030E (w/ AMENDMENT 1), DETAIL SPECIFICATION, DUMMY LOADS, ELECTRICAL, COAXIAL AND STRIPLINE, GENERAL SPECIFICATION FOR (13 MAR 2008) [SUPERSEDING MIL-PRF-39030C and MIL-C-39030B]., This specification covers the qualification and general requirements for coaxial and stripline electrical dummy loads (see 6.1).
Ident. Num:
MIL-DTL-39032 
  Rev. Num:

MIL-DTL-39032E (w/AMENDMENT 1), DETAIL SPECIFICATION, RESISTORS, PACKAGING OF (16 AUG 2005)., This specification covers the requirements for the preservation, packing, and container marking of all types of resistors and associated accessories which are primarily FSC 5905.
Ident. Num:
MIL-DTL-3922 
  Rev. Num:

MIL-DTL-3922C (w/ AMENDMENT 1)., DETAIL SPECIFICATION FLANGES, WAVEGUIDE, GENERAL PURPOSE, GENERAL SPECIFICATION FOR (24 MAY 2006)., This specification covers the general requirements for general purpose waveguide flanges that are used to couple mechanically and electrically two sections of waveguides or waveguide parts (see 6.2).
Ident. Num:
MIL-DTL-3950G 
  Rev. Num:

MIL-DTL-3950G, DETAIL SPECIFICATION, SWITCHES, TOGGLE, ENVIRONMENTALLY SEALED, GENERAL SPECIFICATION FOR (17 DEC 203) [SUPERSEDING MIL-S-3950F]., This specification covers the requirements for environmentally sealed toggle switches.
Ident. Num:
MIL-DTL-398 
  Rev. Num:

MIL-DTL-398D (AMENDMENT 1), MILITARY SPECIFICATION, DETAIL SPECIFICATION, RDX (CYCLOTRIMETHYLENETRINITRAMINE) (17 APR 1999) [SUPERSEDING MIL-R-398C]., This amendment forms a part of MIL-R-398D, dated 12 December 1996, and is approved for use by all Departments and Agencies of the Department of Defense.
Ident. Num:
MIL-DTL-398 
  Rev. Num:

MIL-DTL-398D, MILITARY SPECIFICATION, DETAIL SPECIFICATION RDX (CYCLOTRIMETHYLENETRINITRAMINE) (12 DEC 1996) [SUPERSEDING MIL-R-398C]., This specification covers the requirements, examinations and tests for two types of RDX for use in explosive compositions as follows: (see 6.1). Type I - RDX made by the nitric acid process (see 6.8). Type II - RDX made by the acetic anhydride process (see 6.8).
Ident. Num:
MIL-DTL-40137 
  Rev. Num:

MIL-DTL-40137F (NOTICE 1), MILITARY SPECIFICATION, CLEVISES, RIGGING, AIR DELIVERY TYPE: GENERAL SPECIFICATION FOR (22 FEB 2006) [S/S By PIA-DTL-40137] [SUPERSEDING MIL-C-40137E]., MIL-DTL-40137F, dated 2 November 2004, is hereby canceled. Future acquisitions for this item may refer to PIA-DTL-40137, "Clevises, Rigging, Air Delivery Type: General Specification For". Users are cautioned to evaluate the replacement for their particular application.
Ident. Num:
MIL-DTL-40137 
  Rev. Num:

MIL-DTL-40137F, MILITARY SPECIFICATION, CLEVISES, RIGGING, AIR DELIVERY TYPE: GENERAL SPECIFICATION FOR (2 NOV 2004) [S/S By PIA-DTL-40137] [SUPERSEDING MIL-C-40137E]., This specification covers the general requirements for three types of air delivery rigging clevises, commonly referred to as shackles.
Ident. Num:
MIL-DTL-43342 
  Rev. Num:

MIL-DTL-43342F, DETAIL SPECIFICATION WEBBING ASSEMBLIES, GENERAL SPECIFICATION FOR (25 APR 2005) [SUPERSEDING MIL-W-43342E]., This document covers requirements for miscellaneous cotton and nylon webbing assemblies used in rigging for airdrop operations.
Ident. Num:
MIL-DTL-43649 
  Rev. Num:

MIL-DTL-43649C, DETAIL SPECIFICATION, PARACHUTES, CARGO, 12, 26, AND 34 FOOT DIAMETER (25 JUN 1997) [SUPERSEDING MIL-P-43649B (GL)]., This specification covers the requirements for three cargo parachute assemblies and the separate components thereof.
Ident. Num:
MIL-DTL-43649 
  Rev. Num:

MIL-DTL-43649D, DETAIL SPECIFICATION, PARACHUTES, CARGO, 12, 26, AND 34 FOOT DIAMETER (25 APR 2005)., This specification covers the requirements for three cargo parachute assemblies and the separate components thereof.
Ident. Num:
MIL-DTL-43685 
  Rev. Num:

MIL-DTL-43685C, DETAIL SPECIFICATION WEBBING AND TAPE, TEXTILE, ARAMID FIBER (1 NOV 2005)., This specification covers webbing and tape made from aramid fiber.
Ident. Num:
MIL-DTL-44048 
  Rev. Num:

MIL-DTL-44048H, DETAIL SPECIFICATION, COATS, CAMOUFLAGE PATTERN, COMBAT (30 NOV 2000) [SUPERSEDING MIL-C-44048G]., This document covers the requirements for camouflage pattern, single-breasted combat coats.
Ident. Num:
MIL-DTL-45204 
  Rev. Num:

MIL-DTL-45204D, DETAIL SPECIFICATION GOLD PLATING, ELECTRODEPOSITED (29 June 2007)., (SUPERSEDING MIL-G-45204C 7 June 1983 w/AMENDMENT 3 9 June 1993), This specification covers electrodeposited gold plating on metallic surfaces (see 6.1).
Ident. Num:
MIL-DTL-45444 
  Rev. Num:

MIL-DTL-45444C (AMENDMENT 1), DETAIL SPECIFICATION, HMX (CYCLOTETRAMETHYLENETETRANITRAMINE) (17 APR 1999) [SUPERSEDING MIL-H-45444B (AR)]., This amendment forms a part of MIL-DTL-45444C, dated 26 November 1999, and is approved for use by all Departments and Agencies of the Department of Defense.
Ident. Num:
MIL-DTL-45444 
  Rev. Num:

MIL-DTL-45444C (NOTICE 1), DETAIL SPECIFICATION, HMX (CYCLOTETRAMETHYLENETETRANITRAMINE) (20 APR 2004) [SUPERSEDING MIL-H-45444B (AR)]., MIL-DTL-45444C, dated 17 April 1999, has been reviewed and determined to be valid for use in acquisition
Ident. Num:
MIL-DTL-45444 
  Rev. Num:

MIL-DTL-45444C, DETAIL SPECIFICATION, HMX (CYCLOTETRAMETHYLENETETRANITRAMINE) (26 NOV 1996) [SUPERSEDING MIL-H-45444B (AR)]., This specification covers requirements, examinations and test for two grades of HMX for use in explosive compositions.
Ident. Num:
MIL-DTL-45913 
  Rev. Num:

MIL-DTL-45913C, DETAIL SPECIFCATION, NUTS, SELF-LOCKING, HEXAGON, PREVAILING TORQUE (30 APR 1998) (SUPERSEDING MIL-N-45913B]., This specification establishes mechanical and performance requirements for prevailing-torque hexagon locknuts.
Ident. Num:
MIL-DTL-46162 
  Rev. Num:

MIL-DTL-46162E, DETAIL SPECIFICATION, FUEL, DIESEL, REFEREE GRADE (8 NOV 2002) [SUPERSEDING MIL-F-46162D]., This specification covers two types of referee fuel (see 1.2 and 6.1), for use in research, development and verification testing of all compression-ignition engines, diesel- powered auxiliary units, gas turbine engine driven ground vehicles, mobile electric power generators and other fuel handling supply items designed to operate with either fuel conforming to A-A-52557 or MIL-DTL-83133.
Ident. Num:
MIL-DTL-46593 
  Rev. Num:

MIL-DTL-46593B (w/ AMENDMENT 1), DETAIL SPECIFICATION PROJECTILE, CALIBERS .22, .30, .50, AND 20 mm FRAGMENT-SIMULATING (11 AUG 2008) [SUPERSEDING MIL-P-46593A (MU)]., This specification covers fragment-simulating projectiles used in ballistic testing (see 6.1).
Ident. Num:
MIL-DTL-49285 
  Rev. Num:

MIL-DTL-49285A, DETAIL SPECIFICATION, CABLES, SPECIAL PURPOSE, ELECTRICAL, ALUMINUM FOIL SHIELDED PAIRS, TRIPLETS, OR QUADS, GENERAL SPECIFICATION FOR (12 FEB 2008) [SUPERSEDING MIL-C-49285]., This document covers cables composed of polyester-backed aluminum foil shielded pair, triplet, and quad configurations.
Ident. Num:
MIL-DTL-4946 
  Rev. Num:

MIL-DTL-4946D, DETAIL SPECIFICATION, ANTENNA ASSEMBLY AT-197( )/GR (8 JAN 2008) [SUPERSEDING MIL-A-4946B]., This specification covers the requirements for one type of discone antenna assembly, designed to operate at an impedance of 50 ohms, within the frequency range of 225 through 500 megahertz (MHz)(see 6.1).
Ident. Num:
MIL-DTL-4 
  Rev. Num:

MIL-DTL-4M, DETAIL SPECIFICATION TIRES AND INNER TUBES (NON-AIRCRAFT); PACKAGING OF (10 JAN 1997). This specification covers the preservative, packing, and marking for shipment and storage of: Vehicle (non-aircraft) tires, pneumatic; inner tubes, pneumatic tires; and tires with flaps.
Ident. Num:
MIL-DTL-5015 
  Rev. Num:

MIL-DTL-5015H (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, CIRCULAR THREADED, AN TYPE, GENERAL SPECIFICATION FOR (18 MAY 2000) (Superseding MIL-C-5015G)., This supplement forms a part of MIL-DTL-5015H, dated 18 May 2000. The documents listed in this supplement have been organized to provide information to assist users with the proper selection of connectors.
Ident. Num:
MIL-DTL-5015 
  Rev. Num:

MIL-DTL-5015H, DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, CIRCULAR THREADED, AN TYPE, GENERAL SPECIFICATION FOR (18 MAY 2000)(SUPERSEDING MIL-C-5015G)., This specification is approved for use by all Departments and Agencies of the Department of Defense.. This specification covers circular threaded electrical connectors with solder or removable crimp contacts (both front and rear release). These connectors are for use in electronic, electrical power, and control circuits (see 6.1).
Ident. Num:
MIL-DTL-50700 
  Rev. Num:

MIL-DTL-50700A, DETAIL SPECIFICATION, INITIATOR, PROPELLANT ACTUATED, JAU-2/A25 METAL PARTS ASSEMBLY (18 OCT 2005) [SUPERSEDING MIL-I-50700 (MU)]., This specification covers Initiator, Propellant Actuated, JAU-2/A25, Metal Parts Assembly. The assembly will ultimately be loaded and used in conjunction with other propellant actuated devices in aircrew emergency escape systems.
Ident. Num:
MIL-DTL-5070 
  Rev. Num:

MIL-DTL-5070E, DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR (22 SEP 2000) [SUPERSEDING MIL-A-5070D]., This supplement forms a part of MIL-DTL-5070E, dated 22 September 2000.
Ident. Num:
MIL-DTL-5070 
  Rev. Num:

MIL-DTL-5070F (W/ AMENDMENT 1), DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR (30 MAY 2007)., This specification covers general requirements for adapter, hose to tube, pipe, and flange, reusable - hydraulic, fuel, and oil lines.
Ident. Num:
MIL-DTL-5070 
  Rev. Num:

MIL-DTL-5070F (W/ SUPPLEMENT 1), DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR (15 JUN 2007)., This supplement forms a part of MIL-DTL-5070F, dated 10 December 2006.
Ident. Num:
MIL-DTL-5070 
  Rev. Num:

MIL-DTL-5070F, DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR (10 DEC 2006) [SUPERSEDING MIL-A-5070D]., This specification covers general requirements for adapter, hose to tube, pipe, and flange, reusable - hydraulic, fuel, and oil lines.
Ident. Num:
MIL-DTL-53039 
  Rev. Num:

MIL-DTL-53039B, DETAIL SPECIFICATION COATING, ALIPHATIC POLYURETHANE, SINGLE COMPONENT, CHEMICAL AGENT RESISTANT (8 JUN 2005) [SUPERSEDING MIL-C-53039A]., This specification covers single component, chemical agent resistant, aliphatic polyurethane coating for use as a finish coat on military combat equipment. The coating is lead and hexavalent chromium free and has a maximum of 420 grams/liter (3.5 pounds/gallon) volatile organic compounds for type I and a maximum of 180 grams/liter (1.5 pounds/gallon) volatile organic compounds with zero volatile hazardous air pollutants for type II.
Ident. Num:
MIL-DTL-53072 
  Rev. Num:

MIL-DTL-53072C, DETAIL SPECIFICATION, CHEMICAL AGENT RESISTANT COATING (CARC) SYSTEM APPLICATION PROCEDURES AND QUALITY CONTROL INSPECTION (6 JUN 2003) [SUPERSEDING MIL-C-53072B(ME)]., This document covers the general requirements for application and inspection of the t resistant coating (CARC) system used on tactical military equipment. It is intended for use as a guide in selection of the appropriate materials and procedures, and as a supplement to information available in the below referenced cleaning, pretreating, and coating specifications. The document also includes information on touchup/repair, health and safety guidelines, environmental restrictions, national stock numbers (NSN) for CARC and CARC-related materials, and application equipment and techniques (see 6.5).
Ident. Num:
MIL-DTL-5421 
  Rev. Num:

MIL-DTL-5421C, DETAIL SPECIFICATION, TUBES, PITOT, ELECTRICALLY HEATED, AIRCRAFT (13 JUL 2007) [SUPERSEDING MIL-T-5421D]., This specification covers all types of two-wire electrically heated pitot tubes for use with airspeed indicators.
Ident. Num:
MIL-DTL-5423 
  Rev. Num:

MIL-DTL-5423D (SUPPLEMENT 1), DETAIL SPECIFICATION, BOOTS, DUST AND MOISTURE SEAL (FOR TOGGLE AND PUSH-BUTTON SWITCHES, CIRCUIT BREAKERS, AND ROTARY-ACTUATED PARTS), GENERAL SPECIFICATION FOR (5 APR 2002) [SUPERSEDING MIL-B-5423C]., This supplement forms a part of MIL-DTL-5423D, dated 5 April 2002.
Ident. Num:
MIL-DTL-5423 
  Rev. Num:

MIL-DTL-5423D, DETAIL SPECIFICATION, BOOTS, DUST AND MOISTURE SEAL (FOR TOGGLE AND PUSH-BUTTON SWITCHES, CIRCUIT BREAKERS, AND ROTARY-ACTUATED PARTS), GENERAL SPECIFICATION FOR (5 APR 2002) [SUPERSEDING MIL-B-5423C]., This specification covers the general requirements for molded silicone rubber boots which can be used on component parts such as toggle and pushbutton switches, circuit breakers, and rotary-actuated parts such as rotary switches, variable resistors, capacitors, inductors, and transformers. The boots protect the component parts-actuating mechanism from sand, dust, water and other contaminants, and seal the panel on which the component parts are mounted.
Ident. Num:
MIL-DTL-5498 
  Rev. Num:

MIL-DTL-5498F, DETAIL SPECIFICATION ACCUMULATORS, HYDRAULIC, CYLINDRICAL 3000 PSI, AIRCRAFT (22 JAN 2008) (SUPERSEDING MIL-A-5498E)., This specification covers hydraulic accumulators having a single-shell design with a piston type separator for use in aircraft hydraulic systems at rated pressures ranging to 3,000 pounds per square inch (psi) between the temperature range of -65 degrees F to 275 degrees F.
Ident. Num:
MIL-DTL-5500 
  Rev. Num:

MIL-DTL-5500E, DETAIL SPECIFICATION CAP, HIGH PRESSURE AIR VALVE (5 NOV 2007)., This specification covers one type and grade of high-pressure air valve cap suitable for use in aircraft hydraulic systems.
Ident. Num:
MIL-DTL-55116 
  Rev. Num:

MIL-DTL-55116C (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS: MINIATURE AUDIO, FIVE-PIN AND SIX-PIN GENERAL SPECIFICATION FOR (22 MAR 2004) [SUPERSEDING MIL-C-55116B]., This supplement forms a part of MIL-DTL-55116C, dated 22 March 2004
Ident. Num:
MIL-DTL-55116 
  Rev. Num:

MIL-DTL-55116C, DETAIL SPECIFICATION CONNECTORS: MINIATURE AUDIO, FIVE-PIN AND SIX-PIN GENERAL SPECIFICATION FOR (22 MAR 2004) [SUPERSEDING MIL-C-55116B]., This specification covers waterproof, polarized, five and six contact electrical connectors (plugs and receptacles) for use in audio frequency circuits at 60 volts maximum potential and 0.5 amperes maximum current.
Ident. Num:
MIL-DTL-5516 
  Rev. Num:

MIL-DTL-5516D, DETAIL SPECIFICATION, PACKING, PREFORMED, PETROLEUM HYDRAULIC FLUID RESISTANT, 160F (71C) (15 MAY 2008) [SUPERSEDING MIL-P-5516C]., This specification covers preformed packings for use where resistance to hydraulic fluid conforming to specification MIL-PRF-5606 is required at temperatures from -65 to 160F (-54 to 71C).
Ident. Num:
MIL-DTL-55302 
  Rev. Num:

MIL-DTL-55302F, DETAIL SPECIFICATION, CONNECTORS, PRINTED CIRCUIT SUBASSEMBLY AND ACCESSORIES (13 MAR 2003) [SUPERSEDING MIL-C-55302E]., This specification covers connectors (plugs and receptacles) for printed circuit subassembly and their accessories, for use with single-sided printed wiring, double-sided printed wiring, and multilayer printed wiring conforming to IPC-D275 and MIL-PRF-31032 , respectively (see 6.1). Contact termination types available (see 3.1) are crimp, dip solder, flex, hand solder, and wire wrappost.
Ident. Num:
MIL-DTL-55330 
  Rev. Num:

MIL-DTL-55330C, MILITARY SPECIFICATION, CONNECTORS, ELECTRICAL AND FIBER OPTIC, PACKAGING OF (8 JUN 2001) [SUPERSEDING MIL-C-55330B]., This specification covers the requirements for the preservation, packing, and container marking of all types of electrical and fiber optic connectors (including interconnectors, splices, couplers, splitters, mixers, and associated accessories) which are primarily in FSCs 5935, 6005, and 6060 (see 6.1)
Ident. Num:
MIL-DTL-5541 
  Rev. Num:

MIL-DTL-5541F, DETAIL SPECIFICATION, CHEMICAL CONVERSION COATINGS ON ALUMINUM AND ALUMINUM ALLOYS 11 JUL 2006) [SUPERSEDING MIL-C-5541E]., This specification covers chemical conversion coatings formed by the reaction of chemical conversion materials with the surfaces of aluminum and aluminum alloys.
Ident. Num:
MIL-DTL-55507 
  Rev. Num:

MIL-DTL-55507F, DETAIL SPECIFICATION, SHELTER, ELECTRICAL EQUIPMENT (WITH OR WITHOUT EQUIPMENT), PACKAGING OF (9 jul 1997) [MIL-S-55507E(CR)]., This specification covers the performance requirements for packaging of the following Shelters, Electrical Equipment, with or without equipment, for shipment and in-transit storage: S-141( )/G S-250E/G 1-1/4T (M561 and M715) S-144( )/G S-250( )/G 1-1/4T (M561 and M715) S-144( )/G 3/4T S-250/G and S-250E/G 1-1/4 HMWWV S-144( )/G 1-1/4T S-280( )/G S-250/G S-318( )/G S-250( )/G S-318( )/G 3/4T and 1-1/4T (M561 or M715)
Ident. Num:
MIL-DTL-5624 
  Rev. Num:

MIL-DTL-5624U, DETAIL SPECIFICATION TURBINE FUEL, AVIATION, GRADES JP-4 and JP-5 (5 JAN 2004)., This specification covers two grades of aviation turbine fuel NATO F-40 (JP-4) and NATO F-44 (JP-5) (see 6.1).
Ident. Num:
MIL-DTL-5755 
  Rev. Num:

MIL-DTL-5755D, DETAIL SPECIFICATION, MIRROR, REARVIEW, NONMAGNETIC, GENERAL REQUIREMENTS FOR (FOR AERONAUTICAL USE) (30 MAY 2007) [SUPERSEDES MIL-M-5755C]., This specification covers the general requirements for aircraft nonmagnetic rearview mirrors.
Ident. Num:
MIL-DTL-5765 
  Rev. Num:

MIL-DTL-5765G, DETAIL SPECIFICATION, STRAND, WIRE, ARMORED STEEL (5 JAN 1996)., This specification covers armored steel tow target cable. The terms "strand" and :cable" as referred to in this specification are defined in 6.3.3 and 6.3.1.
Ident. Num:
MIL-DTL-5815  
  Rev. Num:

MIL-DTL-5815G, DETAIL SPECIFICATION, ANTENNA, AIRBORNE, UHF - BAND, GENERAL SPECIFICATION FOR (8 JAN 2007) [SUPERSEDING MIL-A-5815E]., This specification covers the general requirements for ultra high frequency (UHF) band airborne antenna.
Ident. Num:
MIL-DTL-6000 
  Rev. Num:

MIL-DTL-6000D, DETAIL SPECIFICATION HOSE, RUBBER, AIRCRAFT, FUEL, OIL, COOLANT, WATER, AND ALCOHOL (20 SEP 2007)., This specification covers the requirements for hose, rubber, aircraft, fuel, oil, coolant, water, and alcohol, for use in aircraft engine applications.
Ident. Num:
MIL-DTL-6054 
  Rev. Num:

MIL-DTL-6054G, DETAIL SPECIFICATION DRUM, METAL-SHIPPING AND STORAGE (4 SEP 2007) [SUPERSEDING MIL-D-6054F].,This specification covers new cylindrical drums to be used as exterior shipping containers (see 6.1).
Ident. Num:
MIL-DTL-60584 
  Rev. Num:

MIL-DTL-60584B (AR) (W/AMENDMENT 1), DETAIL SPECIFICATION, PROJECTILE, 155 MILLIMETER - SMOKE, WP, METAL PARTS ASSEMBLY, M110A2 (20 SEP 2006) [SUPERSEDING MIL-DTL-60584B(AR)]., This specification covers the manufacturing and assembly of the Projectile, 155MM, Smoke, WP, M110A2 Metal Parts. (See 6.1).
Ident. Num:
MIL-DTL-6060 
  Rev. Num:

MIL-DTL-6060E, DETAIL SPECIFICATION, BAGS, WATER VAPOR PROOF, HEAT-SEALABLE, COMPLEX (12 AUG 2004) [SUPERSEDING MIL-E-6060D]., This specification covers heat-sealable, water vapor proof bags of complex construction for use in military preservation applications.
Ident. Num:
MIL-DTL-62474 
  Rev. Num:

MIL-DTL-62474F (AMENDMENT 1), DETAIL SPECIFICATION LAMINATE: ARAMID-FABRIC-REINFORCED, PLASTIC (21 MAY 2008)., This specification covers an aramid fabric-reinforced plastic laminate for use in composite armor systems.
Ident. Num:
MIL-DTL-62474 
  Rev. Num:

MIL-DTL-62474F (w/AMENDMENT 1 INCORPORATED), DETAIL SPECIFICATION LAMINATE: ARAMID-FABRIC-REINFORCED, PLASTIC (21 MAY 2008 ) [SUPERSEDING MIL-PRF-62474C & MIL-L-62474B]., This specification covers an aramid fabric-reinforced plastic laminate for use in composite armor systems.
Ident. Num:
MIL-DTL-6363 
  Rev. Num:

MIL-DTL-6363H, DETAIL SPECIFICATION LAMPS, INCANDESCENT, AIRCRAFT SERVICE GENERAL SPECIFICATION FOR (30 SEP 1997) (SUPERSEDING MIL-L-6363G)., This specification provides the general and environmental performance requirements for incandescent lamps intended for use primarily in military aircraft applications.
Ident. Num:
MIL-DTL-64159 
  Rev. Num:

MIL-DTL-64159 (INTERIM AMENDMENT 1), DETAIL SPECIFICATION COATING, WATER DISPERSIBLE ALIPHATIC POLYURETHANE, CHEMICAL AGENT RESISTANT (6 MAR 2007)., This specification covers water-dispersible, chemical agent resistant, aliphatic polyurethane coatings for use as a finish coat on all military tactical equipment, which includes ground, aviation and related support assets. The materials are free of hazardous air pollutants (HAP-free), lead and chromate (hexavalent chromium) free, and have a maximum volatile organic compound (VOC) content of 220 g/L (1.8 lb/gal) as packaged.
Ident. Num:
MIL-DTL-64159 
  Rev. Num:

MIL-DTL-64159, DETAIL SPECIFICATION COATING, WATER DISPERSIBLE ALIPHATIC POLYURETHANE, CHEMICAL AGENT RESISTANT (30 JAN 2002)., This specification covers water-dispersible, chemical agent resistant, aliphatic polyurethane coatings for use as a finish coat on all military tactical equipment, which includes ground, aviation and related support assets. The materials are free of hazardous air pollutants (HAP-free), lead and chromate (hexavalent chromium) free, and have a maximum volatile organic compound (VOC) content of 220 g/L (1.8 lb/gal) as packaged.
Ident. Num:
MIL-DTL-6645 
  Rev. Num:

MIL-DTL-6645J, DEPARTMENT OF DEFENSE DETAIL SPECIFICATION, PARACHUTES, PERSONNEL, GENERAL SPECIFICATION FOR (31 AUG 2001) [SUPERSEDING MIL-P-6645H]., This specification covers the general and specific requirements for personnel parachutes and components thereof, as well as specific manufacturing instructions.
Ident. Num:
MIL-DTL-700 
  Rev. Num:

MIL-DTL-700B, DETAIL SPECIFICATION, ENAMEL, DECK, INTERIOR, GRAY, (FORMULA NO. 20L) (30 JUN 1998) [SUPERSEDING JAN-P-700 AND DOD-E-700A]., This specification covers a 340 grams per liter (g/L) (maximum) [2.8 pounds per gallon (lb/gal) (maximum)] volatile organic content (VOC) gray, interior deck enamel (Formula No. 20L) for shipboard use as a general purpose interior deck enamel for application to either primed steel or aluminum (see 6.1). Product is supplied in a single can and used as supplied.
Ident. Num:
MIL-DTL-7034 
  Rev. Num:

MIL-DTL-7034F w/AMENDMENT 1, DETAIL SPECIFICATION, PULLEYS, GROOVE, ANTI-FRICTION BEARING, GREASE LUBRICATED, AIRCRAFT, GENERAL SPECIFICATION FOR (25 AUG 2005)., This specification covers requirements for single groove pulleys with antifriction bearings.
Ident. Num:
MIL-DTL-71026 
  Rev. Num:

MIL-DTL-71026A (AR), MILITARY SPECIFICATION MAGAZINE, CARTRIDGE, SOFT PACK, REUSABLE, M249, 5.56MM MACHINE GUN, GENERAL SPECIFICATION FOR (6 JUN 2000) [SUPERSEDING MIL-M-71026]., This specification covers the Magazine, Cartridge, Soft Pack, Reusable, M249, 5.56mm Machine Gun, hereafter referred to as the magazine (see 6.1).
Ident. Num:
MIL-DTL-7560 
  Rev. Num:

MIL-DTL-7560/1A, DETAIL SPECIFICATION VALVE ASSEMBLY, OXYGEN CYLINDER, BAILOUT (22 JAN 1999)., This specification sheet is approved for use by all Departments and Agencies of the Department of Defense.
Ident. Num:
MIL-DTL-7560 
  Rev. Num:

MIL-DTL-7560D, DETAIL SPECIFICATION VALVE ASSEMBLY, OXYGEN CYLINDER, BAILOUT (20 JUN 1997)., This specification covers manually operated, oxygen cylinder bailout valve assemblies.
Ident. Num:
MIL-DTL-7567 
  Rev. Num:

MIL-DTL-7567C, DETAIL SPECIFICATION PARACHUTES, PERSONNEL, DETAIL MANUFACTURING INSTRUCTIONS FOR (30 OCT 2002) [SUPERSEDING MIL-P-7567B]., This specification covers detail instructions relative to the dimensions, tolerances, repair procedures and other specific manufacturing instructions to be used in the assembly of personnel parachutes. The personnel parachutes covered include the chest, seat, back, troop, training, rescue, integrated, maneuverable, and special purpose.
Ident. Num:
MIL-DTL-75 
  Rev. Num:

MIL-DTL-75K, DETAIL SPECIFICATION ELECTRON TUBES, PACKAGING OF (16 JAN 2007)., This specification covers the requirements for the preservation, packing, and container marking of electron tubes and associated accessories (see 6.1).
Ident. Num:
MIL-DTL-7620 
  Rev. Num:

MIL-DTL-7620D, DETAIL SPECIFICATION, PARACHUTES AND COMPONENTS, CARGO, EXTRACTION AND DECELERATION, GENERAL SPECIFICATION FOR (30 OCT 2002) [SUPERSEDING MIL-P-7620C]., This Specification cover cargo, extraction and deceleration parachute assemblies and components.
Ident. Num:
MIL-DTL-7700 
  Rev. Num:

MIL-DTL-7700G (USAF), DETAILED SPECIFICATION FLIGHT MANUALS, AIR REFUELING PROCEDURES, AND ABBREVIATED CHECKLISTS (13 MAY 2002)., This specification covers the requirements for the preparation of four (4) types of flight manuals and three (3) types of abbreviated flight manual checklists for all types of aircraft. This specification contains appendices which will allow for the tagging of flight manual information for digital delivery to the government. These will allow the flight manual to be prepared in either a paper or electronic presentation. Appendices A through C provide the Document Type Definitions (DTD) required to prepare the manuals specified herein. Adherence to this specification is essential to assure maximum standardization of the flight manual program; however, requirements that are not applicable to a specific aircraft will not be included. Further, any features applicable to a specific aircraft, but not specified herein, will be included in the manual unless waived by the acquiring activity (see 6.2).
Ident. Num:
MIL-DTL-781 
  Rev. Num:

MIL-DTL-781D, DETAIL SPECIFICATION TERMINAL, WIRE ROPE SWAGING, GENERAL SPECIFICATION FOR (15 AUG 1997) [SUPERSEDING MIL-T-781C]., This specification covers wire rope terminals designed for attachment to wire rope by swaging.
Ident. Num:
MIL-DTL-781 
  Rev. Num:

MIL-DTL-781H (w/ AMENDMENT 2), DETAIL SPECIFICATION TERMINAL, WIRE ROPE SWAGING, GENERAL SPECIFICATION FOR (12 OCT 2007)., This specification covers wire rope terminals designed for attachment to wire rope by swaging.
Ident. Num:
MIL-DTL-7990 
  Rev. Num:

MIL-DTL-7990C, DETAIL SPECIFICATION, TRANSMITTER, TEMPERATURE, ELECTRICAL RESISTANCE, -70 TO +300C (20 SEP 2007) [SUPERSEDING MIL-T-7990B]., This specification covers electrical resistance temperature transmitters used in aircraft in conjunction with electrical resistance temperature indicators.
Ident. Num:
MIL-DTL-81218 
  Rev. Num:

MIL-DTL-81218C (AS), DETAIL SPECIFICATION MANUALS, TECHNICAL: AIRCRAFT ENGINE INTERMEDIATE AND DEPOT MAINTENANCE, PREPARATION OF (WORK PACKAGE CONCEPT) (26 NOV 1997)., This specification covers technical manual content requirements for preparation of aircraft engine intermediate and depot maintenance instructions in work package (WP) format for uninstalled reciprocating and gas turbine engines, including turboprop and turboshaft. This specification also covers requirements for an intermediate maintenance manual supplement for the installation, positioning, and identification of external tubing, cabling, clamping and attaching hardware and a Sequence Control Chart (SCC) that graphically depicts accomplishment of complete engine repair. When specified by the requiring activity, an Illustrated Parts Breakdown (IPB) shall be included.
Ident. Num:
MIL-DTL-81306 
  Rev. Num:

MIL-DTL-81306B, DETAIL SPECIFICATION, TOOL, INSTALLATION FOR ADJUSTABLE PLASTIC AND METAL TIEDOWN STRAPS (30 JAN 2007) [SUPERSEDING MIL-T-81306A]., This specification covers tools used to install SAE-AS23190 tiedown straps on wire bundles (see 6.1).
Ident. Num:
MIL-DTL-81381 
  Rev. Num:

MIL-DTL-81381B, DETAIL SPECIFICATION, WIRE, ELECTRIC, POLYIMIDE-INSULATED, COPPER OR COPPER ALLOY (8 SEP 1998) [SUPERSEDING MIL-W-81381A]., This specification covers polyimide-insulated single conductor electric wires made with tin-coated, silver-coated, or nickel-coated conductors of copper or copper alloy as specified in the applicable specification sheet. The polyimide insulation may be used alone or in combination with other insulation materials.
Ident. Num:
MIL-DTL-81381 
  Rev. Num:

MIL-DTL-81381C (SUPPLEMENT 1), DETAIL SPECIFICATION, WIRE, ELECTRIC, POLYIMIDE-INSULATED, COPPER OR COPPER ALLOY (26 AUG 2005) [SUPERSEDING MIL-W-81381A].
Ident. Num:
MIL-DTL-81381 
  Rev. Num:

MIL-DTL-81381C (W/AMENDMENT 1), DETAIL SPECIFICATION, WIRE, ELECTRIC, POLYIMIDE-INSULATED, COPPER OR COPPER ALLOY (10 JAN 2008) [SUPERSEDING MIL-W-81381A]., This specification covers polyimide-insulated single conductor electric wires made with tin-coated, silver-coated, or nickel-coated conductors of copper or copper alloy as specified in the applicable specification sheet. The polyimide insulation may be used alone or in combination with other insulation materials.
Ident. Num:
MIL-DTL-81381 
  Rev. Num:

MIL-DTL-81381C, DETAIL SPECIFICATION, WIRE, ELECTRIC, POLYIMIDE-INSULATED, COPPER OR COPPER ALLOY (26 AUG 2005) [SUPERSEDING MIL-W-81381A]., This specification covers polyimide-insulated single conductor electric wires made with tin-coated, silver-coated, or nickel-coated conductors of copper or copper alloy as specified in the applicable specification sheet. The polyimide insulation may be used alone or in combination with other insulation materials.
Ident. Num:
MIL-DTL-81706 
  Rev. Num:

MIL-DTL-81706B (w/AMENDMENT 1), DETAIL SPECIFICATION CHEMICAL CONVERSION MATERIALS FOR COATING ALUMINUM AND ALUMINUM ALLOYS (2 MAY 2006) (SUPERSEDING MIL-C-81706]., This specification covers chemical conversion materials used in the formation of coatings by the reaction of the material with the surfaces of aluminum and aluminum alloys.
Ident. Num:
MIL-DTL-81736 
  Rev. Num:

MIL-DTL-81736A (AS), DETAIL SPECIFICATION TAPE, TEXTILE, NYLON, LANDBASED ARRESTING GEAR, 8-INCH (24 AUG 2006)., This specification covers an 8-inch nylon tape having a breaking strength of not less than 150,000 pounds for use on landbased arresting gear.
Ident. Num:
MIL-DTL-82194 
  Rev. Num:

MIL-DTL-82194C, DETAIL SPECIFICATION, ORNAMENTATION - FOR JACKET, MAN'S, EVENING DRESS, OFFICERS' (29 JUL 1997) [SUPERSEDING MIL-O-82194B(MC)]., This specification covers requirements for ornamentation components for the men's evening dress jacket.
Ident. Num:
MIL-DTL-823 
  Rev. Num:

MIL-DTL-823L, DETAIL SPECIFICATION, CLOTH, SERGE, WOOL, WOOL AND NYLON, POLYESTER AND WOOL (13 APR 2005) [SUPERSEDING MIL-C-823K]., This document covers the requirements for wool, wool and nylon, and polyester and wool serge cloth.
Ident. Num:
MIL-DTL-83133F 
  Rev. Num:

MIL-DTL-83133F, DETAIL SPECIFICATION, TURBINE FUEL, AVIATION, KEROSENE TYPE, JP-8 (NATO F-34), NATO F-35, and JP-8+100 (NATO F-37) (11 APR 2008) [SUPERSEDES MIL-T-83133D]., This specification covers three grades of kerosene type aviation turbine fuel, JP-8 (NATO F-34), NATO F-35, and JP-8+100 (NATO F-37). This specification was thoroughly reviewed as a part of acquisition reform. While most of the requirements were converted to performance terms, not all requirements could be converted due to the military-unique nature of the product (see 6.1) and the need for compatibility with deployed systems. The issuance of this specification as "detail" is not intended to constrain technology advances in future systems.
Ident. Num:
MIL-DTL-83133  
  Rev. Num:

MIL-DTL-83133F, DETAIL SPECIFICATION, TURBINE FUEL, AVIATION, KEROSENE TYPE, JP-8 (NATO F-34), NATO F-35, and JP-8+100 (NATO F-37) (11 APR 2008) [SUPERSEDING MIL-T-83144D]., This specification covers three grades of kerosene type aviation turbine fuel, JP-8 (NATO F-34), NATO F-35, and JP-8+100 (NATO F-37). This specification was thoroughly reviewed as a part of acquisition reform. While most of the requirements were converted to performance terms, not all requirements could be converted due to the military-unique nature of the product (see 6.1) and the need for compatibility with deployed systems. The issuance of this specification as "detail" is not intended to constrain technology advances in future systems.
Ident. Num:
MIL-DTL-83296 
  Rev. Num:

MIL-DTL-83296A (SUPPLEMENT 1), DETAIL SPECIFICATION, FITTINGS, CORROSION RESISTANT STEEL, HIGH TEMPERATURE, HIGH PRESSURE (3000 PSI), HYDRAULIC AND PNEUMATIC (29 SEP 2000) [SUPERSEDING MIL-F-83296)., This supplement forms a part of MIL-DTL-83296, dated 29 September 2000.
Ident. Num:
MIL-DTL-83296 
  Rev. Num:

MIL-DTL-83296A, DETAIL SPECIFICATION, FITTINGS, CORROSION RESISTANT STEEL, HIGH TEMPERATURE, HIGH PRESSURE (3000 PSI), HYDRAULIC AND PNEUMATIC (29 SEP 2000) [SUPERSEDING MIL-F-83296)., This specification covers the general requirements for corrosion resistant steel fittings used with high-pressure, high-temperature, hydraulic and pneumatic polytetrafluoroethylene (PTFE) hose.
Ident. Num:
MIL-DTL-83413 
  Rev. Num:

MIL-DTL-83413B, DETAIL SPECIFICATION CONNECTORS AND ASSEMBLIES, ELECTRICAL, AIRCRAFT GROUNDING, GENERAL SPECIFICATION FOR (22 SEP 2005) [SUPERSEDING MIL-C-83413A]., This specification covers electrical aircraft grounding connectors and grounding assemblies, including plugs, receptacles, grounding clamp, connectors, jumper cable assemblies, and other accessories.
Ident. Num:
MIL-DTL-83420 
  Rev. Num:

MIL-DTL-83420M, DETAIL SPECIFICATION, WIRE ROPE, FLEXIBLE, FOR AIRCRAFT CONTROL, GENERAL SPECIFICATION FOR (1 APR 2005) [SUPERSEDING MIL-W-83420]., This specification covers the requirements for carbon steel and corrosion resistant steel aircraft control flexible wire rope. Type I wire rope will be capable of operation within a -65 F to +250 F (-54 C to +121 C) temperature range in wind, dust, fuel, and oil spills, in wash-down and other environmental stresses and aircraft experiences. Type II wire rope will be capable of operation within a -65 F to +200 F (-54 C to +94 C) temperature range in wind, dust, fuel, and oil spills, in wash-down and other environmental stresses and aircraft experiences.
Ident. Num:
MIL-DTL-83488 
  Rev. Num:

MIL-DTL-83488D, DETAIL SPECIFICATION COATING, ALUMINUM, HIGH PURITY (1 APR 1999)., This specification establishes the requirements for coating low alloy steel, stainless steel, aluminum alloy, copper alloy, and titanium alloy parts with high purity aluminum (99 percent plus) (see 6.1).
Ident. Num:
MIL-DTL-83511 
  Rev. Num:

MIL-DTL-83511 (SUPPLEMENT 1), DETAIL SPECIFICATION, HEADSET-MICROPHONE AND HEADSET-ELECTRICAL (MEDIUM NOISE ATTENUATION, HEARING PROTECTIVE), GENERAL SPECIFICATION FOR (11 MAR 2004) [SUPERSEDING MIL-H-83511].
Ident. Num:
MIL-DTL-83511 
  Rev. Num:

MIL-DTL-83511, DETAIL SPECIFICATION, HEADSET-MICROPHONE AND HEADSET-ELECTRICAL (MEDIUM NOISE ATTENUATION, HEARING PROTECTIVE), GENERAL SPECIFICATION FOR (11 MAR 2004) [SUPERSEDING MIL-H-83511]., This specification covers headsets and headset-microphone assemblies intended for use in medium ambient noise level environments of 85-105 dBA SPL (Sound Pressure Level). These headset-microphone assemblies use dynamic earphones of the moving coil type that transform electrical energy into acoustical energy. A complete assembly includes headband, earphone(s) mounted in rigid earcups, with cord assemblies to meet requirements of various military service activities. The assemblies include, as required, a noise canceling microphone and boom.
Ident. Num:
MIL-DTL-83513 
  Rev. Num:

MIL-DTL-83513F, DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, RECTANGULAR, MICROMINIATURE, POLARIZED SHELL, GENERAL SPECIFICATION FOR (22 MAR 2007)., This specification covers polarized shell, microminiature, rectangular connectors.
Ident. Num:
MIL-DTL-83517 
  Rev. Num:

MIL-DTL-83517A, DETAIL SPECIFICATION CONNECTOR, COAXIAL, RADIO FREQUENCY FOR COAXIAL, STRIP OR MICROSTRIP TRANSMISSION LINE GENERAL SPECIFICATION FOR (27 OCT 2005) [SUPERSEDING MIL-C-83517]., This specification covers the general requirements and tests for radio frequency connectors used with coaxial, strip, or microstrip transmission line devices.
Ident. Num:
MIL-DTL-83528 
  Rev. Num:

MIL-DTL-83528C (AMENDMENT 1), DETAIL SPECIFICATION, GASKETlNG MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, EMI/RFI GENERAL SPECIFICATION FOR (15 NOV 2001) [SUPERSEDING MIL-G-83528B]., This amendment forms a part of MIL-DTL-83528C, dated 5 January 2001, and is approved for use by all Departments and Agencies of the Department of Defense.
Ident. Num:
MIL-DTL-83528 
  Rev. Num:

MIL-DTL-83528C (SUPPLEMENT 1A), DETAIL SPECIFICATION, GASKETlNG MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, EMI/RFI GENERAL SPECIFICATION FOR (15 NOV 2001) [SUPERSEDING MIL-G-83528B]., This supplement forms a part of Detail Specification MIL-DTL- 83528C, dated 5 January 2001.
Ident. Num:
MIL-DTL-83528 
  Rev. Num:

MIL-DTL-83528C, DETAIL SPECIFICATION, GASKETlNG MATERIAL, CONDUCTIVE, SHIELDING GASKET, ELECTRONIC, ELASTOMER, EMI/RFI GENERAL SPECIFICATION FOR (5 JAN 2001) [SUPERSEDING MIL-G-83528B]., This specification establishes the general requirements for electrically conductive elastomeric shielding gaskets. These gaskets are intended for use in electromagnetic interference/radio frequency interference suppression applications.
Ident. Num:
MIL-DTL-83739 
  Rev. Num:

MIL-DTL-83739C (w/AMENDMENT 1), DETAIL SPECIFICATION SWITCHES, ANTENNA, RADIO FREQUENCY, SOLID-STATE, GENERAL SPECIFICATION FOR (20 JUN 2007) [SUPERSEDING MIL-S-83739A]., This specification covers the general requirements for solid-state antenna switches for use at radio frequencies (see 6.1).
Ident. Num:
MIL-DTL-85025 
  Rev. Num:

MIL-DTL-85025B (AS), DOD DETAIL SPECIFICATION NATOPS PROGRAM TECHNICAL PUBLICATIONS AND PRODUCTS; STYLE, FORMAT, AND COMMON TECHNICAL CONTENT (28 SEP 2007) [SUPERSEDING MIL-M-85025A(AS) & MIL-C-81222C(AS)]., This specification covers general style, format, and technical content requirements for preparation of Naval Air Training and Operating Procedures Standardization (NATOPS) publications and products.
Ident. Num:
MIL-DTL-85052 
  Rev. Num:

MIL-DTL-85052B, DETAIL SPECIFICATION CLAMP, LOOP, CUSHION, GENERAL SPECIFICATION FOR (30 MAR 2005)., This specification establishes the design and test requirements for clamp, loop, cushion, primarily intended for general clamping of tubing for aircraft hydraulic systems.
Ident. Num:
MIL-DTL-85110 
  Rev. Num:

MIL-DTL-85110B, DETAIL SPECIFICATION, BAR, REPEATABLE RELEASE HOLDBACK (RRHB), AIRCRAFT LAUNCHING, GENERAL REQUIREMENT FOR (22 SEP 1997) [SUPERSEDES MIL-B-85110A(AS)., This specification establishes the requirements for the design, construction, performance, and test of the repeatable release holdback bar (RRHB) for use on carrier-type aircraft.
Ident. Num:
MIL-DTL-85470 
  Rev. Num:

MIL-DTL-85470B (NOTICE 1), DETAIL SPECIFICATION, INHIBITOR, ICING, FUEL SYSTEM, HIGH FLASH NATO CODE NUMBER S-1745 (24 MAR 2004) [SUPERSEDING MIL-I-85470A].
Ident. Num:
MIL-DTL-85470 
  Rev. Num:

MIL-DTL-85470B, DETAIL SPECIFICATION, INHIBITOR, ICING, FUEL SYSTEM, HIGH FLASH NATO CODE NUMBER S-1745 (15 JUN 1999) [SUPERSEDING MIL-I-85470A]., This specification covers the requirements for one type and grade of a high flash, fuel system icing inhibitor soluble in aircraft turbine engine fuel. This inhibitor is primarily composed of diethylene glycol monomethyl ether and is commonly referred to as DiEGME.
Ident. Num:
MIL-DTL-85670 
  Rev. Num:

MIL-DTL-85670C, DETAIL SPECIFICATION, ANTENNA, BROADBAND, AS-3191/A, AS-3792/A, AND AS-3793/A (16 MAY 2007) [SUPERSEDING MIL-A-85670A(AS)]., This specification establishes the design, performance, and acceptance requirements for AS-3191/A, AS-3792/A, and AS-3793/A broadband antennas, hereinafter referred to as the antenna. The separately nomenclatured antennas differ only in surface finish and color. The antenna is a universal blade type to be used in aircraft equipped with the AN/ARC-182(V) radio set. The antenna is an aircraft fuselage mounted blade enclosed element. The antenna is a broadband, fix tuned, exhibits omnidirectional radiation pattern, and is vertically polarized for radiating and receiving radio waves in the 30-88 MHz, 108-174 MHz, and 225-400 MHz communication bands.
Ident. Num:
MIL-DTL-85 
  Rev. Num:

MIL-DTL-85H (NOTICE 1), DETAIL SPECIFICATION WAVEGUIDES, RIGID, RECTANGULAR GENERAL SPECIFICATION FOR (15 APRIL 2005). MIL-DTL-85H, dated 22 June 2000, has been reviewed and determined to be valid for use in acquisition
Ident. Num:
MIL-DTL-87161 
  Rev. Num:

MIL-DTL-87161F, DETAIL SPECIFICATION, WIRE STRAND, NON-FLEXIBLE, FOR AIRCRAFT APPLICATION (1 APR 2005) [SUPERSEDING MIL-W-87161]., This specification covers the requirements for carbon steel and corrosion resistant steel wire strand used in aircraft application other than over sheaves. (CAUTION: See application limitations in 6.1.)
Ident. Num:
MIL-DTL-8777 
  Rev. Num:

MIL-DTL-8777E, WIRE, ELECTRICAL, SILICONE-INSULATED, COPPER, 600-VOLT, 200 DEGREES C (21 MAY 2007) [SUPERSEDING MIL-W-8777C]., This specification covers single conductor wire with a silicone primary insulation capable of continuous operation at 600 volts and a maximum conductor temperature of 200 degrees C (392 degrees F). These wires are suitable for use in aircraft and missiles using any combination of electrical loading and ambient temperature, provided the maximum conductor temperature is not exceeded. The wires covered by this specification are not intended as fire-resistant wires.
Ident. Num:
MIL-DTL-87929 
  Rev. Num:

MIL-DTL-87929C (AMENDMENT 1), DETAIL SPECIFICATION TECHNICAL MANUALS, OPERATION AND MAINTENANCE INSTRUCTIONS IN WORK PACKAGE FORMAT (FOR USAF EQUIPMENT) (14 FEB 2002) [SUPERSEDING MIL-PRF-87929B].
Ident. Num:
MIL-DTL-87929 
  Rev. Num:

MIL-DTL-87929C, DETAIL SPECIFICATION TECHNICAL MANUALS, OPERATION AND MAINTENANCE INSTRUCTIONS IN WORK PACKAGE FORMAT (FOR USAF EQUIPMENT) (1 FEB 2000) [SUPERSEDING MIL-PRF-87929B]., This detail specification covers the requirements for preparation of equipment Operation and Maintenance (O&M) Technical Manuals (TM) in Work Package (WP) and Subordinate Work Package (SWP) formats. Manuals, using the WP and SWP concept described within this specification, are intended for use at Intermediate and Depot levels on all equipment and at Organizational level for equipment not using the MIL-PRF-83495 maintenance manual concept. In addition ot "paper" delivery, this specification provides for standard generalized markup language (SGML) Document Type Definitions (DTD) usage (see appendixes A through L) required for electronic data delivery. All appendixes are intended for compliance when required.
Ident. Num:
MIL-DTL-8878 
  Rev. Num:

MIL-DTL-8878K (SUPPLEMENT 1), DETAIL SPECIFICATION, TURNBUCKLES, POSITIVE SAFETYING (8 NOV 2006)., This supplement forms a part of MIL-DTL-8878K, dated 8 November 2006. MS SHEETS MS21251 - Turnbuckle Body, Clip Locking. MS21252 - Clevis End, Turnbuckle, Clip Locking. MS21253 - Clevis End, Turnbuckle, Clip Locking (for Bearing). MS21254 - Eye End, Turnbuckle, Clip Locking. MS21255 - Eye End, Turnbuckle, Clip Locking (for Wire Rope). MS21256 - Clip, Locking, Turnbuckle. MS33736 - Turnbuckle Assemblies, Clip Locking of.
Ident. Num:
MIL-DTL-8878 
  Rev. Num:

MIL-DTL-8878K, DETAIL SPECIFICATION, TURNBUCKLES, POSITIVE SAFETYING (8 NOV 2006)., This specification covers positive safetying turnbuckle component parts.
Ident. Num:
MIL-DTL-8954 
  Rev. Num:

MIL-DTL-8954C, DETAIL SPECIFICATION, BASE AND ACCESSORIES, AIRPORT MARKER LIGHTS, GENERAL SPECIFICATION FOR (24 OCT 2006) [SUPERSEDES MIL-B-8954B]., This specification covers the general requirements for bases, base plate assemblies, adapter plates, covers, frangible couplings, cable clamps, and gaskets used to install airport semiflush and elevated lights.
Ident. Num:
MIL-DTL-915 
  Rev. Num:

MIL-DTL-915G (SUPPLEMENT 1), DETAIL SPECIFICATION, CABLE, ELECTRICAL, FOR SHIPBOARD USE, GENERAL SPECIFICATION FOR (22 AUG 2002) [SUPERSEDING MIL-C-915F & MIL-C-24145].
Ident. Num:
MIL-DTL-915 
  Rev. Num:

MIL-DTL-915G, DETAIL SPECIFICATION, CABLE, ELECTRICAL, FOR SHIPBOARD USE, GENERAL SPECIFICATION FOR (22 AUG 2002) [SUPERSEDING MIL-C-915F & MIL-C-24145]., This specification covers electrical cable for Navy shipboard applications.
Ident. Num:
MIL-DTL-9401 
  Rev. Num:

MIL-DTL-9401C, DETAIL SPECIFICATION, CANOPY, PARACHUTE, RING SLOT, GENERAL SPECIFICATION FOR CONSTRUCTION OF (12 MAY 2003) [SUPERSEDING MIL-C-9401B]., This specification covers the general construction requirements of a parachute canopy which is characterized by concentric rings of cloth separated from each other by slots and designated as the ring slot parachute canopy.
Ident. Num:
MIL-DTL-9419 
  Rev. Num:

MIL-DTL-9419/2E, DETAIL SPECIFICATION SHEET SWITCHES, TOGGLE, FOUR POSITION ON, MOMENTARY, CENTER OFF (.600 DIA) (25 APR 2003)., The requirements for acquiring the product described herein shall consist of this specification and MIL-DTL-9419.
Ident. Num:
MIL-DTL-9419 
  Rev. Num:

MIL-DTL-9419G, DETAIL SPECIFICATION, SWITCH, TOGGLE, MOMENTARY, FOUR-POSITION ON, CENTER OFF, GENERAL SPECIFICATION FOR (25 MAR 2008)., This specification covers four-position, momentary on, center off, positive action switch with free return to the off position.
Ident. Num:
MIL-DTL-9479 
  Rev. Num:

MIL-DTL-9479E (w/ AMENDMENT 1), DETAIL SPECIFICATION SEAT SYSTEM, UPWARD EJECTION, AIRCRAFT, GENERAL SPECIFICATION FOR (16 NOV 2007)., This specification covers the general requirements for adjustable, upward, aircraft ejection seat systems.
Ident. Num:
MIL-DTL-9479 
  Rev. Num:

MIL-DTL-9479E, DETAIL SPECIFICATION SEAT SYSTEM, UPWARD EJECTION, AIRCRAFT, GENERAL SPECIFICATION FOR (17 SEP 1999)., This specification covers the general requirements for adjustable, upward, aircraft ejection seat systems.
Ident. Num:
MIL-DTL-9490 
  Rev. Num:

MIL-DTL-9490E, DETAIL SPECIFICATION, FLIGHT CONTROL SYSTEMS - DESIGN, INSTALLATION AND TEST OF PILOTED AIRCRAFT, GENERAL SPECIFICATION FOR (22 APR 2008) [SUPERSEDING MIL-F-9490D (USAF)] [S/S BY SAE-AS94900]., This specification establishes general performance, design, develop, and quality assurance requirements for the flight control systems of manned piloted aircraft. Flight Control Systems (FCS) includes all components used to transmit flight control commands from the pilot or other sources to appropriate force and moment producers. Flight control commands may result in control of aircraft flight path, attitude, airspeed, aerodynamic configuration, ride, and structural modes. Among components included are the pilots controls, dedicated displays and logic switching, transducers, system dynamic and air data sensors, signal computation, test devices, transmission devices, actuators, and signal transmission lines dedicated to flight control- Excluded are aerodynamic surfaces, engines, helicopter rotors, fire control devices, crew displays and electronics not dedicated to flight control. The interfaces of flight control systems with related subsystems are defined.